- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1832 R/B, страница 7
7
ENGLISH
Small brush (25)
The brush is intended to collect dust from
the surface of the furniture, presence of pile
prevents polished surface of the furniture from
damages.
Crevice attachment (26)
The attachment is intended for cleaning
radiators, crevices, corners and between sofa
pillows.
Attachment for furniture upholstery (27)
Attachment is intended to clean fabric surface
of upholstered furniture.
Turbo-brush for floor/carpets (28)
The turbo brush (28) can be used to clean floors,
rugs and carpets with long or short pile, and is
ideal for picking up animal fur. The cylindrical
brush with hard bristles rotates under the ac-
tion of the air current and its bristles effectively
remove animal fur and loose carpet and rug fi-
bers.
Operating instructions
- Before using the vacuum cleaner, pull the
power cord out to the desired length and
insert the plug into an outlet.
- Yellow mark on the power cord warns you
about the maximal power cord length.
- Never pull the power cord past the red mark.
Attention!
Always turn on the vacuum cleaner only
with the installed container for dust and
rubbish (9) filled with water, the filter
unit (10), air pipe (22), output НЕРА filter
and input and output foam filters. Always
check whether the filters are installed
properly.
To turn on the vacuum cleaner press the On/•
Off button (3) (pic.7).
After the cleaning is over, press the On/Off •
button (3) again and take the plug out of the
socket.
Press the power cord-winding button• (2), and
hold the winding cord with your hand to pre-
vent entanglement and damage (pic.8).
Between operations, use the brush “parking” •
place (1).
To carry the vacuum cleaner after operation, •
use the handle (4).
Maintenance
When water in the container (9) becomes dirty •
(suction power can be reduced), you should
pour it out, to proceed with cleaning, fill the
bin with clear water, refer to the “Cleaning of
the container for dust and rubbish” section.
Note:
It is recommended to pour out dirty
water from the container and wash the
container and the removable parts after
each usage.
Before removing the container it is necessary •
to switch the unit by pressing the button (3),
and then take the plug out of the socket.
Cleaning the vacuum cleaner
Cleaning the container for dust and rubbish
(9)
Open the lid (5), pulling the lid opening but-•
ton (7) (pic.1).
Holding the side edges of the container for •
dust and rubbish (9) carefully, in order not
to spill water, remove the container from the
body of the vacuum cleaner (pic. 2).
Remove the filter unit (10), holding the handle •
on the separator lid (21) (pic. 3).
Pour put dirty water from the container.•
Remove the air pipe (22) and wash it under a •
warm water jet (pic.9)
Wash the container (9).•
Set the air pipe on its place (22) (pic.9).•
Cleaning the filter unit (10)
Keep the filter unit (10), which is set in the
container for dust and rubbish, clean (9).
Perform cleaning of the filter unit after several
cleanings or as it gets dirty.
Remove the separator lid (21), turning it •
anticlockwise (pic.11).
Wash the lid (21) under warm water if •
necessary or if the filter (20) is very dirty,
remove it from the lid (21) and wash separately
(pic.19, 20). Dry the filter (20) and set it on
the lid (21) (pic.20).
Turn over the filter, holding the “cyclone” filter •
(23), remove it clockwise and remove from
the separator (24) (pic. 12, 13).
VT-1832 R B.indd 7VT-1832 R B.indd 7 05.08.2011 15:36:0805.08.2011 15:36:08
Ваш отзыв будет первым