- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1832 R/B, страница 6
6
ENGLISH
Never use the vacuum cleaner to pick up wa-•
ter or other liquids, burning or smoke-emit-
ting cigarettes, matches, smoldering ashes
or fine dust such as from plaster, cement,
flour or cinder.
Do not use the vacuum cleaner: •
- without the container for dust and rubbish;
- without the removable details;
- output НЕРА-filter and all foam filters are not
installed.
Check the power cord and the power plug •
for damages regularly. If there are some
damages in the power cord, the power
plug, or if the unit malfunctions, apply to the
authorized service center.
The unit is intended for household usage only; •
commercial usage of the vacuum cleaner is
prohibited.
STORE THE INSTRUCTIONS IN A CONVENIENT
PLACE
SAFETY PRECAUTIONS
Do not use the vacuum cleaner in the imme-•
diate vicinity of very hot surfaces, next to ash
trays, or where flammable liquids are stored.
Before cleaning, remove sharp objects from •
the floor to avoid damage of the filters.
If suction power decreases abruptly while •
cleaning, immediately turn off the vacuum
cleaner and check the telescoping tube or
flexible hose for foreign objects. Turn off the
vacuum cleaner, and then unplug it from the
power outlet. Clear the obstruction and only
then proceed with cleaning.
Assembling the vacuum cleaner
- Unpack the vacuum cleaner and check it for
damages. If there are any damages in the
unit, do not use it.
- Before turning on the vacuum cleaner, make
sure that the voltage of the mains corresponds
to the voltage of the vacuum cleaner.
- Always turn off the vacuum cleaner and
unplug it from the outlet before changing the
brushes/attachments, and before performing
maintenance.
Filling the container with water for dust and
rubbish collection (9)
Open the lid (5), by pulling the lid opening •
button (7) (pic.1).
Take the side edges on the container for dust •
and rubbish (9) remove it from the body of the
vacuum cleaner (pic. 2).
Remove the filter unit (10), holding the handle •
on the separator lid (21) (pic. 3).
Fill the container (9) with water until the MAX •
mark.
Note:
Necessary quantity of water is 1300 ml.
Put the filter unit (10) into the container (9).•
Put the container (9) into the body of the vac-•
uum cleaner.
Check whether the container (9) and the filter •
unit (10) are set properly.
Close the lid (5). •
Note:
- Do not exceed the MAX mark.
- Do not use the vacuum cleaner if there is no
water in the container (9).
Attaching and removing the flexible hose (13)
Insert the end of the flexible hose (11) in the •
air inlet (8).
Insert the hose until a click, which confirms •
proper connection (pic. 4).
To remove the flexible hose end press the •
clamp (12) and disconnect the hose.
Attaching the telescoping extension pipe
(15) and the attachments
Attach the telescoping extension pipe (15) to •
the flexible hose handle (14).
Extend the lower part of the telescoping pipe •
to the desired length by pressing the clamp
button (pic.5).
Select the desired attachment• : carpet/
floor brush (16), small brush (25), crevice
attachment (26), attachment for furniture
surface (27) and connect it to the telescoping
extension pipe (15) (pic.6) and the
attachments (25, 26, 27) can be set on the
flexible hose handle (14).
Carpet/floor brush (16)
Set the switch on the brush to the desired
position (depending on the type of the surface
you wish to clean).
6
ENGLISH
VT-1832 R B.indd 6VT-1832 R B.indd 6 05.08.2011 15:36:0805.08.2011 15:36:08
Ваш отзыв будет первым