- Тип техники
- Бренд
Просмотр инструкции кофеварки Vitek VT-1526, страница 4
4
ENGLISH
• Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package only.
• Keep the unit in a dry cool place out of reach
of children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
– Take the coffee maker out of the package and
remove the packaging materials.
– Check the unit for damages; do not use it in
case of damages.
– Make sure that operating voltage of the cof-
fee maker corresponds to the voltage of your
mains.
– Before using the coffee maker for the first
time, wash all removable parts (2, 7, 15, 16, 17)
with warm water and neutral detergent and
dry them.
BEFORE USING THE UNIT
Note: - if you switched the coffee maker on and
don’t do anything, the coffee maker would be
switched off in 30 minutes.
Before making coffee wash the coffee maker
boiler.
• Remove the water tank (2), fill it with cold
water up to the «MAX» mark and install it back
to its place.
• Insert the coffee filter (15 or 16) into the
holder (7), do not add ground coffee into the
filter (15 or 16).
• Install the filter holder (7) back to its installa-
tion place. The filter holder (7) ledges should
match the groves on the boiler, after that turn
the filter holder (7) handle to the utmost right
position «LOCK».
• Place a suitable cup on the tray grid (6).
• Insert the power plug into the mains socket.
• Switch the coffee maker on by pressing the
button (13) «
», the button (13) illumination
will light up and start flashing. Wait until water
in the boiler heats up, the button (13) illumina-
tion will be glowing constantly.
• Press the manual coffee/water supply but-
ton (10) «
», the pump will switch on for 3 sec-
onds; after a pause the pump will be switched
on and the water will be supplied constantly.
After the cup is filled with water, switch the
water supply off by pressing the button (10)
«
» again, pour the water out of the cup.
• Depending on the cup capacity repeat this
procedure several times until the boiler is
clean.
ATTENTION!
– Do not remove the filter holder (7) during cof-
fee maker operation.
– To remove the filter holder (7) turn the filter
holder handle to the left until bumping and
remove the holder (7).
Rinsing the cappuccinator pipe (4)
• Make sure that there is enough water in the
water tank (2).
• Place a suitable cup under the cappuccina-
tor pipe (4).
• Switch the coffee maker on by pressing the
button (13) «
».
• Press the steam supply on button (9) « »
and wait until the button (9) illumination stops
flashing and glows constantly.
• Slowly turn the steam supply control knob (3)
«OFF--- +», steam will start going out from
the cappuccinator pipe (4) tip (5), be care-
ful while operating with outgoing steam, after
10-15 seconds set the control knob (3) to the
position «OFF».
• Switch the coffee maker off by pressing the
button (13) «
».
• Remove the tray grid (6), remove the tray and
pour the water out of it, install the tray an the
grid (6) back to their places.
• The coffee maker is ready for operation.
MAKING ESPRESSO
• Remove the water tank (2), fill it with cold
water up to the «MAX» mark and install it back
to its place. Make sure that the water level in
the tank (2) is not below the mark «MIN», reg-
ularly add water to the tank (2).
• Put ground coffee in the filter (15 or 16) using
the measuring spoon (17), slightly tamp the
coffee with the back side of the measuring
spoon (17).
IM VT-1526.indd 4 28.12.2017 16:03:20
Ваш отзыв будет первым