- Тип техники
- Бренд
Просмотр инструкции увлажнителя воздуха Vitek VT-2332 W, страница 5
5
E N G L I S H
«Night» mode on/off button (10)
– Touch the button (10) to switch the «night»
mode on, only the «mist» release intensity
icon will be shown on the display (11).
– To switch the «night» mode off touch the but-
ton (10) again.
Note: - in the «night» mode the unit will operate
at the preset «mist» release intensity and the dis-
play (11) illumination will not bother you.
Low water level indication
– When the water tank (4) is empty, the unit will
be switched off, there will be sound signals,
and the empty water tank icon will be flashing
red on the display (11).
– Switch the unit off touching the button (14),
remove the nozzle (1) and the water tank (4).
Fill the tank (4) with water (see the chapter
«Using the air humidifier»). First place the
filled water tank (4) on the air humidifier body
(7) and then install the nozzle (1).
– Switch the unit on for further operation.
CLEANING AND CARE
WARNING! Always switch the unit off and
unplug it before cleaning.
Hard water causes appearance of mineral scale
in the process chamber (6) and in the water
tank (4) that leads to improper operation of the
unit. To avoid it:
– use filtered, boiled and settled water. If tap
water is hard, it is recommended to mix tap
water with distilled water in proportion 1:1. If
tap water is too hard, mix it with distilled water
in proportion 1:2 or use distilled water only.
– Change water in the water tank (4) twice a
week.
– Thoroughly wash the process chamber (6)
and the water tank (4) with neutral detergent
solution twice a week.
– To clean the sprayer add 5-10 drops of
detergent on it and wait for approximately
10-15 minutes. Remove the scale from the
sprayer surface with a soft brush, and then
wash the process chamber (6) with neutral
detergent solution.
– Rinse the process chamber (6) and the water
tank (4) several times. Wipe the process
chamber (6) with a soft cloth.
– Clean the air humidifier body (7) with a soft,
slightly damp cloth, and then wipe it dry.
– Remove and clean the air inlet grid (12) and
the foam filter as it becomes dirty.
Notes:
– Do not immerse the air humidifier body into
water or other liquids.
– Do not use abrasives or solvents for cleaning
the «sprayer».
– As a cleaning agent for the «sprayer» you can
use a descaling agent for kettles, strictly fol-
lowing the instruction for this substance.
STORAGE
– Pour the water out of the tank and make sure
that the process chamber and the «sprayer»
are dry before taking the unit away for storage.
– Do not keep the unit with water inside the tank
or the process chamber.
– Keep the air humidifier away from children in
a dry cool place.
TROUBLESHOOTING
Malfunction Possible causes Troubleshooting
No “mist” The unit is connected improperly Check if the power plug is inserted into the
mains socket.
The unit is off Switch the unit on by pressing the button (13).
Water tank is empty or there isn’t
enough water in the tank.
Fill the water tank with enough water.
Foreign smell
appears
during the
operation
First use Disconnect the unit from the mains. Remove the
water tank, remove the lid and pour the water
out of the water tank, then leave the water tank
in a dry cool place for 12 hours.
Dirty or stale water Unplug the unit, remove the water tank, remove
the lid, pour the water out of the water tank
and clean the tank (as described in the chapter
“Cleaning and care”), then fill it with clean water.
IM VT-2332.indd 5 26.06.2017 11:42:46
Ваш отзыв будет первым