- Тип техники
- Бренд
Просмотр инструкции увлажнителя воздуха Vitek VT-2332 W, страница 4
4
ENGLISH
• Never use the unit if the power cord or the
power plug is damaged, if the unit works
improperly or after it was dropped.
• Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package only.
• For environment protection do not discard the
unit with usual household waste after its ser-
vice life expiration; apply to a specialized cen-
ter for further recycling.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage under
cold (winter) conditions, it is necessary to
keep it for at least three hours at room tem-
perature.
There may be water spots in the air humidi-
fier, this is normal, as the unit has undergone
factory quality control.
– Unpack the unit, remove any stickers and
package materials that can prevent unit oper-
ation. Check the unit for damages. In case of
damages do not switch the unit on.
– Before plugging the unit in make sure that
your home mains voltage corresponds to the
unit operating voltage.
Notes:
Use the air humidifier at the room temperature
from +10° С to +40°С, and relative humidity less
than 80%.
Water temperature should not exceed +40°С.
USING THE AIR HUMIDIFIER
– Remove the nozzle (1).
– Take the water tank by the handle (2) and
remove it from the unit body (7).
– Turn over the tank (4), remove the lid (5) rotat-
ing it counterclockwise.
– Fill the tank (4) with necessary amount of
water, insert the lid (5) into the water inlet and
turn it clockwise until bumping.
– First place the filled water tank (4) back to its
place and then install the nozzle (1).
– Wait till the process chamber (6) is filled with
water.
– Insert the power plug into the mains socket.
– Switch the unit on touching the button (14),
you will hear a sound signal and the unit will be
switched on with the «mist» release intensity
2; the digital indications of relative room air
temperature and «mist» release intensity icon
will be shown on the display (2), the illumina-
tion (8) will light up.
– To switch the air humidifier off touch the but-
ton (14) again.
– Unplug the unit.
Notes:
– The operation mode selection and setting
buttons are sensory, you just need to touch
the button to switch the necessary operation
mode on.
– The room air temperature indications may be
slightly different from the readings of another
thermometer.
– Draughts or other air flows may significantly
affect the air temperature indications in the
room.
OPERATION MODE CONTROL BUTTONS
ON/OFF button (14)
– Touch the button (14) to switch the unit on
and touch the button (14) again to switch the
unit off.
«Mist» release intensity button (13)
– Consequently touch the button (13) to select
the «mist» release intensity, the «mist» release
intensity will be shown on the display with digi-
tal symbols «1-2-3».
«1» – low intensity,
«2» – medium intensity,
«3» – high intensity.
Timer setting button (9)
– Consequently touch the button (9) to set up
the timer within the range from 1 to 12 hours
(with 1 hour step); the timer operation time will
be shown on the display (11).
– When the set time is reached the unit will be
switched off.
– To switch the timer off touch the button (9)
until the symbol «0» appears on the dis-
play (11).
IM VT-2332.indd 4 26.06.2017 11:42:46
Ваш отзыв будет первым