- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1845 R/B, страница 6
6
10. Do not allow any objects to block the out-
lets of the vacuum cleaner.
If any of the outlets is blocked, do not switch
on the appliance.
11. Watch the hairs, the ends of the cloths
hanging down, fingers or other parts of the
body are not near by any vacuum cleaner
inlets.
12. Always switch the appliance off by ON/OFF
button before unplugging it from the wall
outlet.
13. Take special care while cleaning the stair-
cases.
14. Do not use the appliance for collecting the
inflammable liquids (gasoline, dissolvent,
etc.). Do not use the appliance at the plac-
es where such a liquids are stored.
15. Do not use the appliance to pick up wa-
ter or other liquids, burning or gleaming
cigarettes, matches, smoldering ash, thin
powders, like plaster, concrete, flour or ash
dust, sharp and cutting things. This may
course serious electric motor damages.
Remember, warranty does not extend to
such damages.
16. Do not use the vacuum cleaner if dust col-
lecting container and filters are not installed
properly.
17. Hold the power cord by your hand while
winding it. Do not allow the plug to strike on
the floor.
KEEP THIS MANUAL IN TOUCH, USE IT (IF
REQUIRED) FOR REFERENCE.
PRECAUTIONS
If suction power is suddenly down while clean-
ing, switch the vacuum cleaner off immediately
and check out if its telescopic tube or flexible
hose is blocked. Switch off the vacuum clean-
er, then unplug the cord from the wall outlet,
remove the blocking substance, and continue
cleaning.
• Do not operate the vacuum cleaner too close
to the heated surfaces, cigarette butts, and
in the areas where the flammable or combus-
tible liquids are kept.
• Before to insert the plug into the wall outlet,
you should make sure that your hand is dry.
• Before you start using the vacuum cleaner,
please remove the large or sharp objects
from the floor in order to prevent the filters
damages.
• To disconnect the power cord from the wall
outlet hold the plug, not the electrical cable.
Assembling vacuum cleaner
Unpack the vacuum cleaner completely and
ensure there are no any damages. Any factory
defects or transportation damages are the sub-
jects of VITEK warranties.
Verify the vacuum cleaner voltage meets the
mains voltage in your supply line before switch-
ing the appliance on.
Always switch off and unplug the vacuum clean-
er to change the nozzles or for maintenance.
1. Connecting and removing flexible hose
(Pic.1)
Insert the flexible hose tip (4) into the air inlet
(6). Insert the hose up to the click indicating
the connection is proper. To remove the flexible
hose press fixing button (5), and detach it.
2. Connection of telescopic tubes and
brushes
- Connect the telescopic extension tube (2) to
the flexible hose handle (3) (Pic. 2). Press fix-
ing button and pull out the lower part of the
telescopic tube up to the length you need
(Pic. 3).
- Choose the nozzle you need: turbo brush (1),
crevice nozzle (27), nozzle for cleaning the
furniture coverings (29), small brush (28) or
floor/carpet brush (30), and connect it to the
telescopic extension tube (Pic. 4).
Using brushes and nozzles
Turbo brush for floor/carpets (1)
Use turbo brush (1) to clean the floor, carpets
and covers with long and short nap, it is ideal
for cleaning the wool out from the carpets. Cyl-
inder brush with coarse nap is rotated by the
air flow, its nap brushes the wool and removes
small dirties out of the carpet nap very effec-
tively.
Notice: to avoid a carpet damage caused by
the brush rotation, do not use the turbo brush
for cleaning the carpets with very long nap,
more then 15 cm length. Do not touch the elec-
trical wires by the rotating the brush.
ENGLISH
1845.indd 61845.indd 6 14.04.2010 9:29:4414.04.2010 9:29:44
Ваш отзыв будет первым