Просмотр инструкции пылесоса Vitek VT-1828 PP, страница 6
6
ENGLISH
take the power plug out of the socket before
replacing the brush attachments and before
cleaning the dust bin (9).
OPERATION
Safety measures
• Do not use the vacuum cleaner near hot sur-
faces, ashtrays and in places where inflamma-
ble liquids are stored and used.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it off
immediately and check the telescopic pipe and
the flexible hose for obstruction. Switch the vac-
uum cleaner off, unplug it, remove the obstruc-
tion and only after that you can continue cleaning.
Attention! You may switch the vacuum cleaner
on only with the dust bin (9), the inlet filter
(23-25) and the outlet filter (27) installed.
Always check if the dust bin (9) and the filters
(23-25 and 27) are installed properly.
– Before using the unit, unwind the power cord to
the required length and insert the power plug
into the mains socket. The yellow mark on the
power cord warns about the maximum cord
length. Do not unwind the power cord further
than the red mark.
– Press the ON/OFF button (4) to switch the vac-
uum cleaner on.
– During the operation you can control the suc-
tion power by turning the suction power control
(5) on the flexible hose handle (13).
– After the unit operation switch the vacuum
cleaner off by pressing the ON/OFF button (4)
and unplug the unit.
– To wind the power cord, press and hold the
button (1), hold the winding cord with the hand
to avoid its whipping and damage.
– Between operations use the brush storage
compartment (3).
– Use the handle (6) for carrying the vacuum
cleaner. Press the handle (6) to extend it.
Attention! Do not use the handle of the dust
bin (9) for carrying the vacuum cleaner.
AUTO SWITCH-OFF FUNCTION
The vacuum cleaner is equipped with an auto
switch-off function in case of motor overheating.
• In case of overheating of the motor unit, the
automatic thermal switch will be on, and the
vacuum cleaner will be switched off.
• In this case remove the power plug from the
mains socket immediately.
• Check the telescopic pipe and the flexible hose
for obstruction and remove the obstruction.
• Let the vacuum cleaner cool down for approx-
imately 30-40 minutes (the cooling time
depends on ambient temperature and can be
longer or shorter).
• Connect the vacuum cleaner to the mains and
switch it on, if the vacuum cleaner can not be
switched on, wait for some more time (see the
previous paragraph), and if the vacuum cleaner
can not be switched on after that as well, this
may mean, that it is otherwise damaged. In
this case contact an authorized service cen-
ter for repair.
CLEANING AND CARE
The maximal dust/rubbish level mark on the dust
bin (9) or the glowing indicator (7) informs you
that dust bin (9) should be cleaned.
It is recommended to clean the dust bin (9) after
every use of the vacuum cleaner to avoid foreign
smell from the dust bin (9).
Detaching the dust bin (9) and removing dust
and garbage from it
– Switch the vacuum cleaner off by pressing the
ON/OFF button (4) and unplug it.
– Detach the flexible hose (12), having pressed
the locks of the flexible hose ending (11).
– Take the dust bin (9) by the handle, press the
release button (8) and remove the dust bin (9)
(pic. 1).
Note: The dust bin (9) can be removed only
if the vacuum cleaner is in horizontal position,
otherwise the release button (8) on the dust bin
(9) lid will be blocked.
– Remove the lid from the dust bin (9) (pic. 2).
– Remove accumulated dust and garbage from
the dust bin (9).
– Wash the dust bin (9) and the lid under warm
water jet and dry them thoroughly.
Note: Before installing the dust bin (9) back to its
place, make sure that the dust bin and its lid are
clean and dry.
Cleaning the inlet filter
Clean the inlet filter (23-25) regularly.
– Remove the dust bin (9).
VT-1828.indd 6 03.06.2014 17:45:11
Ваш отзыв будет первым
Вопросы пользователей
Поиск:
Сортировать:
по дате
c ответами
Ирина
30 июля 2020, Калининград
Подскажите пожалуйста работает ли от аккумулятора автомобильный пылесос VITEK VT-1828 R ?