- Тип техники
- Бренд
Просмотр инструкции культиватора Al-ko MH 7505 VR, страница 24
en
Operation
24 7505 VR / 7505 V2R
Use the depth skid
When the handlebar of the cultivator – and thus
also the depth skid – is pressed down, the speed
of the cultivator decreases or it stops.
When the handlebar of the cultivator – and thus
also the depth skid – is lifted upwards, the speed
of the cultivator increases.
Engaging/releasing reverse gear, 7505 VR
(15)
1. To stop the tiller blades: Release the clutch
lever (15/3).
2. Pull the lever (15/4) for reverse gear upwards
up to the stop.
3. To start the tiller blades: Press the safety but-
ton (15/2) and firmly press the clutch lever
(15/3) on the handlebar (15/1) downwards.
Operating the gear shift, 7505 V2R (16)
The gear lever (16/1) can be used to switch 2
forwards gears and 1 reverse gear. The first for-
wards gear is intended for hard ground; the tiller
blades turn slowly. The second forwards gear is
intended for less hard ground; the tiller blades turn
faster.
1. To stop the tiller blades: Release the clutch
lever (16/3).
2. Turn the gear lever (16/1) in such a way that it
coincides with the required gear on the plate
(16/2) for the gear display (1 = 1st gear, 2 =
2nd gear, R = reverse gear).
3. To start the tiller blades: Press the safety but-
ton (16/4) and firmly press the clutch lever
(16/3) on the handlebar downwards.
Adjusting the sideways position of the hand-
lebar (17)
Sideways adjustment of the handlebar makes it
possible not to walk on the surface already pro-
cessed. The handlebar can be adjusted by 35° to
either side.
1. Pull the cam lever (17/1) upwards. The
handlebar (17/2) disengages from the holder
(17/3).
2. Turn the handlebar (17/2) to the side (left or
right) up to the stop and keep it in this position.
3. Press the cam lever (17/1) down. The hand-
lebar (17/2) is locked in place.
MAINTENANCE AND CARE
WARNING!
Danger of serious injury during main-
tenance and care work!
Persons can be seriously injured by mo-
ving machine parts.
Always switch the motor off and pull
the spark plug connector prior to any
maintenance and care work.
Motor may continue running. After
switching off, make sure that the mo-
tor has stopped.
Always wear work gloves when car-
rying out maintenance and care jobs
on the tiller blades.
Clean the appliance after every use.
Do not spray the machine with water! Pene-
trating water (ignition system, carburettor...)
can lead to malfunctions.
ADVICE
When the device is tilted to the side, the
carburettor must be pointing upwards.
CAUTION!
Danger of pollution due to waste oil
Waste oil that is illegally disposed of, e.g.
in the sewage system, in the ground or
in water, can cause serious pollution.
Always dispose of waste oil in ac-
cordance with legal requirements,
e.g. at waste oil acceptance points.
Every point of sale that sells oil is le-
gally bound to accept waste oil.
Never drain waste oil into the se-
wage system, the ground or into wa-
ter.
Expert inspection is required:
After running into an obstacle
If the motor stops suddenly
If there is gear damage
If the V-belt is defective
If a blade is bent
If the motor shaft is bent
Replacing the gear oil of the chain gear (18)
The gear oil of the chain gear must be replaced
every 100 working hours (amount: 0.5 l, viscosity
SAE 80). The cultivator must be warm in order to
replace the gear oil.
Ваш отзыв будет первым