- Тип техники
- Бренд
Просмотр инструкции культиватора Al-ko MH 7505 VR, страница 23
Start-up
441582_a 23
Mounting the guard plate extension:
1. Place the guard plate extension (11/1) on the
already available guard plate (11/2) as shown
in the figure (11).
2. Attach the guard plate extension to the exis-
ting guard plate with the screws (11/3).
START-UP
Adjusting Bowden cables
See chapter “Maintenance and care".
Adjusting the height of the handlebar (6)
The height of the handlebar depends on your
body height. The handlebar should be at waist
height.
1. Turn both grips (06/5) for the height adjust-
ment of the handlebar open until the handle-
bar can be pressed down or up.
2. Press the handlebar down or up until it is at
the required height.
3. Retighten both grips for the height adjust-
ment.
OPERATION
Fuel fill
See operating instructions of the motor.
Roll the cultivator to the place where it is to
be used (12)
The cultivator is easy to roll to the place of opera-
tion using the transport wheel (12/1).
1. If the transport wheel is folded in: Pull out (di-
rection A) the transport wheel (12/1) on the
wheel mount (12/2). Fold it down into the drive
position and release it so it can lock in place.
2. Lift the cultivator using the handlebar until it is
on the transport wheel (12/1).
3. Push the cultivator to the place of operation.
4. Folding in the transport wheel for tilling: Pull
out (direction A) the transport wheel (12/1) on
the wheel mount (12/2). Fold it upwards into
the horizontal position and release it so it can
lock in place.
Starting and stopping the motor (14)
Starting the motor:
1. Open the petrol cock by pushing the lever
(14/1) in the ON arrow direction.
2. If the motor is cold:
Push the choke lever (14/2) towards the
choke symbol. Only use this position for star-
ting the motor.
3. Adjusting the motor speed or work speed:
Increasing the work speed: Push the control-
ler (14/3) for the motor speed in the “MAX.
(Hare)” direction.
Decreasing the work speed: Push the con-
troller (14/3) for the motor speed in the “MIN.
(Tortoise)” direction.
4. Rotate the gas lever (14/4) to position “1”.
In position “1” the motor runs at the speed set
on the controller. The motor does not start in
position “0”.
5. Use the grip (14/5) to quickly pull out the star-
ter rope and then let it slowly roll up again.
The motor starts to run.
If the motor does not run: Check that all pre-
vious work steps have been carried out and
then pull the starter rope again.
6. When the motor is running smoothly: Slowly
push the choke lever (14/2) back to the stop.
If the motor starts stuttering, push the choke
lever slightly back in the direction of the choke
symbol.
Stopping the motor:
1. Rotate the gas lever (14/4) to position "0".
2. Close the petrol cock (14/1).
Starting and stopping the tiller blades (13)
Starting the tiller blades:
1. Hold the handlebar by the grip (13/1).
2. Press the safety button (13/2).
3. Press the clutch lever (13/3) on the handlebar
firmly downwards.
After the lever has travelled halfway, the tiller bla-
des begin to rotate and the cultivator starts mo-
ving. After the clutch lever has been pressed fully
downwards, the tiller blades have been comple-
tely started.
Stopping the tiller blades:
1. Release the clutch lever (13/3).
The cultivator stops.
Ваш отзыв будет первым