- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1886 B, страница 6
6
ENGLISH
• Extend the telescopic extension pipe (16)
to the required length, having preliminarily
pressed the telescopic pipe lock (17) (pic. 5).
• Select the required attachment: floor/carpet
brush (21), turbo brush (24), small brush (25),
crevice nozzle (26) or upholstery brush (27) and
attach it to the telescopic extension pipe (16).
Using the brush attachments
Floor/carpet brush (21)
Set the switch (20) to the required position
(depending on the type of the surface being
cleaned).
Turbo brush (24)
You can use the turbo brush (24) for cleaning
floors and carpets, it is perfect for removing pet
hair from carpets. The cylindrical hard-bristled
brush is brought to rotation by the air flow, its
bristles comb out pet hair out thoroughly and
sweep the motes out of the carpet pile.
Notes:
– Do not use the turbo brush (24) for cleaning
rugs or carpets with pile longer than 15 mm.
– Do not run the turbo brush (24) over elec-
tric wires.
– Switch the vacuum cleaner off right after
cleaning with the turbo brush (24).
Small brush (25)
The small brush (25) is intended for collecting
dust from furniture surface, pile prevents the
damage of polished furniture surface.
Crevice nozzle (26)
The crevice nozzle (26) is intended for cleaning
radiators, chinks, corners and spaces between
cushions.
Upholstery brush (27)
The attachment (27) is intended for cleaning
fabric surfaces of upholstered furniture.
Attachment holder (18)
Use the attachment holder (18) for easy storage
of attachment during operation,.
OPERATION
Attention! Always switch the vacuum cleaner
on with the installed dust bin (8) filled with
water, make sure that the filters (32, 34, 35,
38, 39) and outlet filters (23) are installed
properly.
Before using the unit, unwind the power cord to
the required length and insert the power plug into
the mains socket. The yellow mark on the power
cord warns about the maximum cord length. Do
not unwind the power cord further than the red
mark.
• Press the ON/OFF button (1) to switch the
vacuum cleaner on.
• During the operation of the unit you can con-
trol the suction power by turning the control
knob (2).
• After the unit operation switch the vacuum
cleaner off by pressing the ON/OFF button (1)
and unplug the unit.
• To wind up the cord, press the button (4), hold
the winding cord with your hand to avoid its
whipping and damage.
• Between operations use the storage (3) by
inserting the brush (21) bracket (19) into it.
• After operation use the handle (5) for carrying
the vacuum cleaner.
Warning:
– Do not use the dust bin handle (7) or aqua fil-
ter tank (11) handle for carrying the unit.
ATTENTION!
If carpets or furniture upholstery have been
pretreated with a stain remover or special
detergents, then a large amount of foam
can appear in the dust bin (8) during opera-
tion, it can come out of the dust bin and get
into the HEPA Filter (39). To prevent appear-
ing of foam, add a special foam-neutralizing
agent – used in wet and dry vacuum clean-
ers – into the aqua filter tank (11). Follow the
foam-neutralizing agent dosage as recom-
mended by the manufacturer.
Vacuum cleaner maintenance during
its operation
Change water as it becomes dirty during the
unit operation. This procedure is described in
the chapter “Filling the aqua filter tank (11) with
water”.
In case the vacuum cleaner’s suction power
decreases, clean all the filters. This procedure is
described in the chapter “CLEANING AND CARE”.
Note:
– Pour dirty water out of the tank (11) and wash
the dust bin (8) after every use of the vacuum
cleaner.
• Before removing the dust bin (8), switch the
vacuum cleaner off preliminarily by pressing
VT-1886.indd 6 23.07.2014 11:42:57
Ваш отзыв будет первым