Бесплатные инструкции на русском языке
  • Тип техники
  • Бренд

Просмотр инструкции акустики Vitek VT-4027-4037, страница 6

Vitek
(2) Make sure the device is properly connected to the audio source.
4. NO SOUND IS COMING FROM THE CENTRAL SPEAKER
(1) Make sure the central speaker is properly connected to the
device.
(2) Make sure the device is properly connected to the audio source.
(3) Increase the volume of the central speaker.
5. NO SOUND IS COMING FROM THE REAR SPEAKERS
(1) Maker sure the rear speakers are connected properly.
(2) Make sure the device is properly connected to the audio source.
NOTE: The central and rear speakers only work if the system is con-
nected to a six-channel audio source (for example, a DVD player with
an AC-3/Dolby Digital decoder) or, if in 3D mode, when connected
through the 2.1 CH audio input.
APPENDIX
When connecting the device to a DVD player with a built-in DD/DTS
decoder, verify the following:
1. When connected through the 5.1 CH. audio input, the 5.1 CH audio
output should be chosen in the player's settings. Playback discs with
AC-3/Dolby Digital 5.1 CH audio tracks.
2. To turn on the subwoofer, make sure that the speaker size in the
player's settings for the front, central and rear speakers is "Small"
and that the subwoofer output is set to "On."
When connecting the device to DVD player, carefully read the operat-
ing instructions for the DVD player.
PRECAUTIONARY MEASURES:
Attention: Please carefully read the points listed below to ensure
safe use of the device.
1. Read the instructions - The safety instructions and operating
rules should be read before using the device.
2. Save the instructions - Save the instructions for future use.
3. Follow the operating rules - All of the safety instructions should
be followed.
4. Warning symbols - Heed the indications of all warning symbols
located on the device's panels or in these instructions.
5. Power source - The device should only be connected to a power
source with the characteristics indicated on the rear panel of the
device or in these instructions.
6. Protecting the power cord - The power cord should be laid out in
such a way that it will not be damaged by external items or its
surroundings.
7. Water and moisture - Do not use the device near reservoirs of
water (for example, bath tubs, sinks, etc).
8. Ventilation - Install the device in a well ventilated room. Do not
install the device on couches, beds or carpets because the
device's ventilation may be blocked.
9. The effects of heat - Do not install the device near heat sources
(for example, radiators, kitchen stoves, etc).
10. Periods of non-use - if the device will not be used for a long peri-
od of time, disconnect the power plug from the electrical outlet.
11. The need for maintenance - Utilize the services of qualified tech-
nicians if:
The power cord is damaged; or
The device body is damaged; or
The device was subjected to rain; or
The device is not functioning properly; or
The device was subjected to shock.
12. Repair service - The consumer should not attempt to repair the
device himself. Use only the services of a qualified technician.
13. Clean the device with a dry, soft clothe only.
14. Turn off the device during thunderstorms or when not in use for a
long period of time.
TECHNICAL CHARACTERISTICS
Power supply: ~220-230 Volts
Output power: 60 W (Subwoofer)
+ 5 x 35 W (Satellite speakers)
Subwoofer speaker: 8"/4 Om
Satellite speakers: 2"/8 Om
Channel separation: >45 dB
Signal/noise ratio: >85 dB
Reproducible frequency band:
35 Hz - 200 Hz (Subwoofer)
150 Hz - 20 KHz (Satellite speakers)
AM/FM Tuner
General FM tuner characteristics:
Frequency band: 87.00 MHz ~108.00 MHz
Frequency tuning step: 50/100 KHz
Intermediate frequency of oscillation:
10.7 MHz
Temperature range: -5 - +70°C
Antenna input impedance: 75 Om
Signal/noise ratio: >45 dB
General AM tuner characteristics:
Frequency band: 522 KHz ~ 1610 KHz
Frequency tuning step: 9/10 KHz
Intermediate frequency of oscillation:
450 KHz
Temperature range: -5 - +70°C
Signal/noise ratio: >45 dB
The technical characteristics of the device may be changed without
prior notice.
Service life – no less than 5 years.
Guarantee
Details regarding guarantee conditions can be obtained from the
dealer from whom the appliance was purchased. The bill of sale or
receipt must be produced when making any claim under the terms of
this guarantee.
This product conforms to the EMC-Requirements as laid
down by the Council Directive 89/336/EEC and to the Low
Voltage Regulation (23/73 EEC)
ENGLISH
6
4027.qxd 04.10.2005 11:16 Page 6
Ваш отзыв будет первым
Задайте вопрос
Ваше имя
E-mail
Вопрос*
Ваш вопрос будет опубликован после проверки
Ваш вопрос опубликован

Смотрите также другие инструкции раздела Vitek