- Тип техники
- Бренд
Просмотр инструкции блендера Vitek VT-3404 BK, страница 4
4
ENGLISH
– Wash the attachments that will contact products with
warm water and a neutral detergent and dry them
thoroughly before use.
– Wipe the motor unit (4), whisk gear (6) and geared lid
of the processor (10) with a soft slightly damp cloth.
Attention!
– Do not immerse the motor unit (4), whisk gear (6),
processing bowl geared lid (10), power cord and
power plug into water or any other liquids.
– Do not put the attachments and bowls in a dish-
washing machine.
OPERATION TIME
Continuous operation time while working with attachments
(5, 7) should not exceed 1 minute. Operation time of the
processor should not exceed 20-30 seconds. Make at
least a two-minute break between operation cycles.
USING THE BLENDER ATTACHMENT
Warning:
– Before assembling, make sure that the power plug
is not inserted into the mains socket.
• Insert the blender attachment (5) into the motor unit
(4), and turn it counterclockwise until bumping.
• Insert the power plug into the mains socket.
• Immerse the blender attachment (5) into the bowl
with products that you want to chop/mix; you can
use the measuring cup (22) for it.
Note: When using the measuring cup (22) for chop-
ping/mixing products, the amount of ingredients
should not exceed 200 ml. Otherwise the mixed
products can splash out.
• To switch the blender on, press and hold the button
(2). Set the required operation speed from 1 to 20
using the control knob (1). Use this operation mode
for mixing liquid products.
• If you press and hold the button (3), the unit will
operate at maximum rotation speed. Use this oper-
ation mode for combined processing of liquid and
hard products.
Notes:
– Products should be put into the bowl before the unit
is switched on.
– Before starting to chop/mix, we recommend to peel
fruit, remove inedible parts, such as bones, and cut
fruit into cubes approximately 2х2 cm in size.
• After you finish using the unit, take the power plug
out of the socket and remove the blender attach-
ment (5), turning it clockwise.
Attention!
– Do not remove the blender attachment (5) during
operation.
– In order not to damage the blades, do not process
too hard products such as cereals, rice, spices, cof-
fee beans, ice, cheese, frozen food.
– If the products are difficult to process, add some liq-
uid into the bowl.
USING THE WHISK
Use the whisk attachment (7) only to beat cream, make
biscuit dough or for mixing ready desserts.
Warning:
– Before assembling, make sure that the power plug
is not inserted into the mains socket.
• Insert the whisk (7) into the gear (6).
• Insert the whisk gear (6) into the motor unit (4), and
turn it counterclockwise until bumping.
• Insert the power plug into the mains socket.
• Sink the whisk (7) into the bowl with products.
• Set the required operation speed from 1 to 20 using
the control knob (1).
• To switch the blender on, press and hold the button
(2). Use this operation mode for mixing liquid products.
• If you press and hold the button (3), the unit will
operate at maximum rotation speed.
• After you finish using the unit, take the power plug
out of the socket, disconnect the whisk (7) from the
gear (6) and disconnect the gear (6) from the motor
unit (4) by turning it clockwise.
Attention!
– Do not use the whisk (7) to make tight dough.
– Products for beating/mixing should be put into the
bowl before the unit is switched on.
USING THE CHOPPING KNIFE
Attention!
– Do not chop very hard products, such as nutmegs,
coffee beans and cereals.
Before you start chopping:
– remove bones, sinews and cartilage from meat.
– cut meat, onion, garlic, carrots etc. into approxi-
mately equal pieces;
– when chopping greens, remove stems of herbs.
Chopping
Warning:
– Before assembling, make sure that the power plug
is not inserted into the mains socket.
– Do not overload the processing bowl!
Caution: the blades are very sharp!
• Set the driving shaft (20) on the axis of the process-
ing bowl (17).
• Remove the plastic protective cover from the blades
of the knife (19) and set the knife (19) on the splines
of the driving shaft (20).
• Put the products into the processing bowl (17).
• Install the geared lid (10) on the bowl (17).
• Press the lock button (16) and turn the geared lid
(10) counterclockwise to the position “
” , release
the lock button (16) and make sure that the geared
lid (10) is fixed properly.
• Place the motor unit (4) on the geared lid (10) and
rotate it clockwise until fixing.
• Insert the power plug into the mains socket.
VT-3404.indd 4 30.10.2013 10:10:49
Ваш отзыв будет первым