- Тип техники
- Бренд
Просмотр инструкции блендера Vitek VT-8517 ST, страница 4
4
ENGLISH
• Do not use the unit if the motor unit body,
the power cord or the plug is damaged, if
the unit works improperly or after it was
dropped.
• Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Keep the unit out of reach of children.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE USING THE UNIT
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
• Unpack the unit completely and remove any
stickers that can prevent unit operation.
• Check the unit for damages; do not use it in
case of damages.
• Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
• Before the first use wash all removable parts
with warm water and neutral detergent and
then dry thoroughly.
• Clean the motor unit with a soft, slightly damp
cloth and then wipe it dry.
• Do not immerse the motor unit into any
liquids or wash it with water.
• Place the blender on a flat stable surface.
ATTENTION! Continuous operation time of
the blender should not exceed 2 minutes;
then switch the unit off and let it cool down
for at least 2 minutes.
• Do not remove the blender bowl and the bowl
lid during the operation.
USING THE BLENDER
• Place the blender bowl (3) on the motor unit
(6) and turn it clockwise until bumping.
• Remove the blender bowl lid (2).
• Put the necessary ingredients into the
bowl (3).
Note:
– Before starting to chop/mix, we recommend
to peel fruit, remove inedible parts, such as
stones, and cut fruit into cubes approximately
2х2 cm in size.
– The blender is not intended for beating eggs,
making potato mash, kneading dough or
extracting fruit or vegetable juice.
– The amount of products to be processed
should not exceed 2/3 of the capacity of
the bowl in which they are processed or be
below the minimal mark of the blender bowl
“500 ml”.
• Close the blender bowl (3) with the lid (2).
• Make sure once again that the blender bowl
(3) is installed correctly and fixed.
• Insert the measuring cup (1) into the lid (2)
opening, matching the corresponding marks
on the measuring cup (1) and the lid (2), and
turn the measuring cup clockwise as far as it
will go.
• Insert the power plug into the mains socket.
Note: The blender will not be switched on if the
blender bowl (3) is installed incorrectly.
• Use the operation mode switch (7) to set the
required rotation speed of the knives:
– «I» (low speed) - for mixing liquid products;
– «II» (high speed) - for liquid and hard prod-
ucts.
• To switch the pulse mode on, set the switch
(7) to the position “P” and hold it for several
seconds.
• During the operation or between the opera-
tion cycles, you can add the required ingre-
dients into the bowl (3). To this end, turn the
measuring cup (1) counterclockwise, match-
ing the corresponding marks, and remove the
measuring cup (1). After adding ingredients
through the lid (2) opening, install the mea-
suring cup (1) back to its place.
• After the unit’s operation is finished, set the
operation mode switch (7) to the “0” position
and unplug the unit.
• Remove the blender bowl (3) from the motor
unit (6) by turning it counterclockwise.
• Remove the measuring cup (1) from the lid
(2).
• Remove the lid (2) from the bowl (3) taking it
by the ledge and take the processed products
out of the bowl (3). If necessary, you can use a
spatula to remove the products.
• After the operation is finished, wash the
blender bowl (3).
Note:
– If food processing is hard, add some liquid
(water, liquor, juice) into the blender bowl (3).
– To chop ice cubes (no more than 10 cubes
sized 2.5 cm x 2.5 cm x 2.5 cm) put them
VT-8517.indd 4 17.02.2016 17:19:54
Ваш отзыв будет первым