- Тип техники
- Бренд
Просмотр инструкции увлажнителя воздуха Vitek VT-2333, страница 5
5
E N G L I S H
CLEANING AND CARE
WARNING!
Before cleaning the air humidifier, always switch
it off, disconnect the power adapter from the
mains and remove the adapter cord connector
from the socket (14).
Hard water causes appearance of mineral scale
in the process chamber (7) and in the water
tank (3) that leads to improper operation of the
unit. To avoid it:
– use water filtered with a domestic filter, boiled
and settled. If tap water is hard, it is recom-
mended to mix tap water with distilled water
in proportion 1:1. If tap water is too hard, mix
it with distilled water in proportion 1:2 or use
distilled water only.
– Change water in the water tank (3) twice a
week.
– Thoroughly wash the process chamber (7)
and the water tank (3) with neutral detergent
solution twice a week.
– To clean the sprayer (9), add 5-10 drops of
detergent on it and wait for approximately
10-15 minutes. Remove the scale from the
sprayer surface with a soft brush, and then
wash the process chamber (7) with a neutral
detergent solution.
– Rinse the process chamber (7) several times.
Wipe the process chamber (7) with a soft
cloth.
– Clean the air humidifier body (10) with a soft,
slightly damp cloth, and then wipe it dry.
– Remove and clean the air inlet grid (13) and
the foam filter as it becomes dirty.
– To remove the foam filter, press on the air inlet
grid (13), extract the container, the foam fil-
ter, clean it and install back to its place, install
the container back to its place; to do this,
press on the air inlet grid (13) until the lock
is tripped.
– To clean the float (5) remove it; to do this lift
it up and remove the front part of the float (5)
from the holder (6) groove, then remove the
rear part. Clean the float (5) from mineral scale.
– Install the float (5) back to its place, to do this
match the ledge on the rear part of the float (5)
with the opening in the installation place (6),
then insert the ledge on the front part of the
float into the holder (6) groove, make sure that
the float (5) is fixed properly (pic. 2).
Notes:
– do not immerse the air humidifier body into
water or other liquids;
– do not use abrasives or solvents for cleaning
the sprayer (9);
– you can use a descaling agent for kettles as a
detergent for the sprayer (9) and the float (5),
strictly following the instruction for this sub-
stance.
STORAGE
– Pour the water out of the tank and make sure
that the process chamber and the sprayer are
dry before taking the unit away for storage.
– Do not keep water inside the tank (3) or the
process chamber (7) of the unit.
– Keep the air humidifier in a dry cool place
away from children and disabled persons.
TROUBLESHOOTING
Problem Possible causes Troubleshooting
No “mist” The unit is connected
improperly
Check if the power plug is inserted into the mains socket.
The unit is off Switch the unit on by pressing the button (15).
Water tank is empty
or there isn’t enough
water in the tank
Fill the water tank with enough water.
Foreign smell
appears during
the operation
First use Disconnect the unit from the mains. Remove the water tank,
remove the lid and pour the water out of the water tank, then
leave the water tank in a dry cool place for 12 hours.
Dirty or stale water Unplug the unit, remove the water tank, remove the lid,
pour the water out of the water tank and clean the tank (as
described in the chapter “Cleaning and care”), then fill it
with clean water.
IM VT-2333.indd 5 10.01.2018 17:04:06
Ваш отзыв будет первым