- Тип техники
- Бренд
Просмотр инструкции увлажнителя воздуха Vitek VT-2331 BK, страница 5
5
E N G L I S H
Control panel (3) and remote control (22) buttons
ON/OFF button (12)
–
Press/touch the button (12) (on the remote con-
trol) to switch the unit on and press/touch it again
to switch the unit off.
Water heating mode on/off button (13)
–
Press/touch the button (13) to switch the water
heating mode on, the corresponding icon will
light up in the operation mode icons (18) row on
the display. To switch the water heating mode
off press/touch the button (13) again, the water
heating icon in the operation mode icons (18)
row will go out.
–
To switch the water tank (4) illumination on or off
press/touch and hold the button (13).
Room relative humidity setting button (14)
–
Consequently press/touch this button to set the
desired level of relative humidity in the room
within the range from 40% to 80% which will be
shown on the display with the icons (21), the
humidity icon will light up on the display in the
operation mode icons (18) row.
–
When the desired humidity level is reached,
the unit will be switched off, when the relative
humidity level decreases, the unit will switch
on.
–
To switch the selected humidity maintenance
mode off press/touch the button (14) until the
flashing symbols «- -» (21) appear on the dis-
play.
Mist release intensity button (15)
–
Consequently press/touch this button to select
the mist release intensity, the mist release inten-
sity will be shown on the display as the icons (19)
in the following order:
–
medium intensity
–
low intensity,
–
high intensity.
–
medium intensity
Timer setting button (16)
–
Consequently press/touch this button to set up
the timer within the range from 1 to 12 hours with
1 hour step which will be shown on the display
with the icons (20) and an icon in the operation
mode icons (18) row.
–
When the set time is reached the unit will be
switched off.
–
To switch the timer off press/touch the but-
ton (16) until the temperature icons (20) appear
on the display.
–
To switch the digital display on or off press/touch
and hold the button (16).
«Night» mode on/off button (17)
–
After pressing/touching this button the unit will
switch to the «night» mode: the icons (19, 20,
21) on the display will go out, and the connection
icon and the night mode icon will be shown in the
operation mode icons (18) row.
–
To switch the display on press/touch the but-
ton (17) again.
Low water level indication
For normal operating mode:
–
When the water tank (4) is empty, the unit will be
switched off, the connection icon will be flash-
ing in the operation mode icons (18) row (if the
unit is not in the «night» mode). If the unit is in the
«night» mode, the unit will be switched off when
the water tank (4) is empty.
–
Switch the unit off with the button (12), remove
the nozzle (5) and the water tank (4). Fill
the tank (4) with water (see the chapter «Using
the air humidifier»). Place the filled water
tank (4) back to its place and then install the
nozzle (5).
–
Switch the unit on for further operation.
For night mode:
–
When the water tank (4) is empty, the unit will
be switched off, the display will not show any
icons.
–
Remove the nozzle (5) and the water tank (4).
Fill the tank (4) with water (see the chapter
«Using the air humidifier»). Place the filled water
tank (4) back to its place and then install the
nozzle (5). The unit will start operating auto-
matically.
CLEANING AND CARE
WARNING! Always switch the unit off
and unplug it before cleaning.
Hard water causes appearance of mineral scale
in the process chamber (10) and in the water
tank (4) that leads to improper operation of the
unit. To avoid it:
–
use filtered, boiled and settled water. If tap water
is hard, it is recommended to mix tap water with
distilled water in proportion 1:1. If tap water is too
hard, mix it with distilled water in proportion 1:2
or use distilled water only.
–
Change water in the water tank (4) twice
a week.
–
Thoroughly wash the process chamber (10) and
the water tank (4) with neutral detergent solution
twice a week.
–
Before cleaning the process chamber (10)
remove the heating element protective lid (9).
–
To clean the sprayer add 5-10 drops of detergent
on it and wait for approximately 10-15 minutes.
IM VT-2331.indd 5 07.04.2017 11:06:46
Ваш отзыв будет первым