- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-8128, страница 5
5
E N G L I S H
make sure that the HEPA filter (20) is installed
properly before setting the dust bin (11) back
to its place.
USING THE VACUUM CLEANER
Safety measures
•
Do not use the vacuum cleaner near hot sur-
faces, such as ashtrays and in places where
inflammable liquids are stored.
•
Take sharp objects away from the floor before
cleaning to prevent unit damage.
•
If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it off
immediately and check the telescopic pipe (4)
and the flexible hose (7) for obstruction. Switch
the vacuum cleaner off, then unplug it, remove the
obstruction and only after that continue cleaning.
USING THE VACUUM CLEANER
ATTENTION! You may switch the vacuum cleaner
on only with the dust bin (11) installed with the HEPA
filter (20) installed in the dust bin, and with the out
-
let HEPA filter (18) installed.
Always check that the filters (18, 20) are installed
properly.
•
Before using the unit, unwind the power cord to
the required length and insert the power plug
into the mains socket.
•
The yellow mark on the power cord indicates the
maximum cord length. Do not unwind the power
cord further than the red mark.
•
Press the on/off button (14) to switch the vac-
uum cleaner on.
•
During the operation you can control the suc-
tion power using the power control (15) and the
manual suction power control (5) on the flexible
hose handle (6). After room cleaning switch the
vacuum cleaner off by pressing the on/off but
-
ton (14) and unplug the unit.
•
To wind the power cord, press the button (16),
hold the winding cord with your hand to avoid its
whipping and damage.
•
During the breaks you can place the brush (1) in
the brush storage (17).
Note: before replacing the brush (1) or the attach
-
ments (24, 25) or cleaning the dust bin (11) switch
the vacuum cleaner off and take the power plug out
of the mains socket.
CLEANING AND MAINTENANCE
Cleaning the dust bin (11)
In order to avoid foreign smell from dust and gar
-
bage it is recommended to remove the dust and
garbage from the dust bin (11) after every room
cleaning.
–
Switch the vacuum cleaner off and unplug it.
–
Holding the handle (12), move the dust bin lock
button (13) and remove the dust bin (11) from the
vacuum cleaner body pulling upwards (pic. 4).
–
Press the dust bin lid release button (22) and
open the dust bin lid (23) (pic. 5).
–
Place the dust bin above the trash bin, turn the
dust bin (11) upside down and remove the dust
and garbage (pic. 6).
–
Close the lid (23) and make sure that the lid (23)
is fixed properly.
–
Install the dust bin (11) back to its place.
Cleaning the HEPA filter (20)
in the dust bin (11)
–
Preliminarily remove dust and garbage from the
dust bin (11) as described above.
–
Remove the HEPA filter (20) (pic. 7).
–
Clean the HEPA filter (20) from dust and gar-
bage and wash the HEPA filter (20) under warm
water jet.
Note:
–
wash the HEPA filter (20), directing the water jet
to the outer side of the HEPA Filter (20).
–
Do not wash the filter (20) in a dishwashing
machine.
–
Dry the filter thoroughly.
–
Do not dry the HEPA filter (20) with a hairdryer.
–
Wash the dust bin (11), wipe it and dry.
–
Install the HEPA filter (20) back to its place.
Note:
–
if you cannot install the dust bin (11) to its place,
check whether the HEPA filter (20) is installed
properly.
–
Install the assembled dust bin (11) back to its
place.
ATTENTION!
Before installing the dust bin (11) into the vacuum
cleaner body make sure that the HEPA filter (20) is
dry and there is no moisture inside the dust bin (11).
Cleaning the outlet HEPA filter (18)
•
Switch the vacuum cleaner off and unplug it.
•
Remove the outlet filter grid (19) by pressing the
clamp, press the clamp and remove the HEPA
filter (18).
•
Wash the HEPA filter (18) under slightly warm
water jet. Do not wash filters in a dishwashing
machine.
•
Dry the HEPA filter (18). Do not dry the HEPA fil-
ter (18) with a hairdryer.
IM VT-8128.indd 5 20.08.2018 12:02:12
Ваш отзыв будет первым