- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1843 B/R/SR, страница 6
6
ENGLISH
to such rugs. Do not run the turbo brush over
power cords and turn off the vacuum cleaner
immediately after you are done using it.
Crevice attachment (23)
The attachment is intended for cleaning of ra-
diators, crevices, corners and between sofa
pillows.
Operating instructions
Before using the vacuum cleaner, pull the
power cord out to the desired length and in-
sert the plug into an outlet. The yellow mark
on the power cord warns about the maximal
length of the cord. Never pull the power cord
past the red mark.
- Always turn on the vacuum cleaner only
with the installed container (7), the cone
filter (20), and the installed НЕРА filters
(15) and (16) and the foam filter (14).
- To turn on the vacuum cleaner press the
On/Off button (11).
- To wind the cord press the power cord-
winding button (12), and hold the winding
cord with your hand to prevent whipping
and damage.
- During operation you can adjust suction
power using the suction control, situated
on the handle of the flexible hose.
Cleaning the vacuum cleaner
Indicator of the dust container filling (10) is
on when it is necessary to clean the container
(7).
- Switch off the unit by pressing the button
(11) and take the plug out of the socket.
- Turn the flexible hose tip (5) anticlockwise
and remove it from the air inlet opening
(6).
- Press the clamp button (8), take the handle
(13) and remove the container (7) from the
body of the vacuum cleaner.
- Open the lid of the container (19), by press-
ing the button (18).
- Remove dust and rubbish from the con-
tainer (7).
- Close the lid(19).
- Place the container (7) on its place.
Note:
- It is recommended to clean the container
(7) and the cone filter (20) each time after
usage of the vacuum cleaner.
Cleaning of the input filters
Keep the НЕРА-filter (15), and the foam filter
(14) clean,
as the operational effectiveness of
you vacuum cleaner depends on it
; clean the
filters after several usages of the unit
and if
they get really dirty – then more often.
- Switch off the unit by pressing the button
(11) and take the plug out of the socket.
- Turn the flexible hose tip (5) anticlockwise
and remove it from the air inlet opening (6).
- Press the clamp button (8), take the handle
(13) and remove the container (7) from the
body of the vacuum cleaner.
- Remove the foam filter (14) and the НЕРА
filter (15).
- Clean the filters (14 and 15) from dust and
rubbish.
- Wash the filters (14 and 15) under warm
tapping water. Do not use a dish wash ma-
chine to wash the filters.
- Dry the filters. Do not use a hairdryer to dry
the НЕРА filter (15).
- Place the filters on their place.
Cleaning the cone filter
- Pull the body of the cone filter (20) and re-
move it.
- Clean the filter (20) from dust and rub-
bish.
- Wash the filter under a water jet.
- Dry and place the cone filter (20) on its
place by matching the arrow on the filter
(20) with the arrow on the body of the con-
tainer (7).
Cleaning of the output НЕРА filter
- Pull the ledge of the input filter grid (17)
and remove it.
- Remove the output НЕРА filter (16), wash it
under a warm water jet and dry. Do not use
a dish wash machine to wash the filter.
- Place the filter (16) on its place and close the
grid (17).
VT_1843_instruk.indd 6VT_1843_instruk.indd 6 01.07.2011 10:43:1301.07.2011 10:43:13
Ваш отзыв будет первым