- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1837 B/R, страница 5
5
E N G L I S H
5
immediate vicinity of very hot surfaces, near
ash-trays or where inflammable liquids are
stored.
• Make sure your hands are dry when you con-
nect the power cord to the outlet.
• Before cleaning, remove sharp objects from
the floor, not to damage pre-filter of HEPA fil-
ter.
• Always take the power plug in order to discon-
nect the device from electrical power; never
pull on the power cord.
PREPARING FOR OPERATION
Fully remove the packing. Before turning on
the device make sure that the voltage of the lo-
cal power supply matches the device operating
voltage.
Always turn off the device and disconnect the
power plug from the outlet when changing the
nozzles and also during maintenance.
USING THE VACUUM CLEANER
• Make sure that the collection container (9)
and filters (20, 21) are installed correctly.
• Insert the flexible hose nozzle (6) into the inlet
air opening (7). To remove the flexible hose,
press the clamp buttons and disconnect the
hose.
• Attach to the hose handle (4) telescopic tube
(2) (Fig.1).
Telescopic tube (2)
• Extend the telescopic tube lower part as need-
ed, for that press the clamp button (Fig.2).
Floor/Carpet brush (1)
• Connect the brush (1) to the telescopic tube
(2) (Fig.3).
• Set the Floor/Carpet switch on the brush to
the needed position, depending on the type of
surface being cleaned (Fig.3).
Furniture brush (22)
• The brush is used specially to clean fabrics
surfaces.
Universal brush (23)
• Is used to clean in radiators, crevices, angles
and between divan cushions.
• The brush is used to collect dust from the fur-
niture surface, the brush nap prevents from
damaging the funiture surface.
INSTRUCTIONS FOR USE
Before the work extend the power cord as de-
sired and insert the cord plug to the power out-
let. Yellow mark on the cord alerts about the
maximum cable length.
Do not extend the cable above the red mark.
Turn on the vacuum cleaner only after the col-
lection container (9) and its filters (20, 21) have
been installed.
• To turn off the device, press the ON/Off button
(11).
• To wind the power cord, press the cord wind
button (12), hold the cord with you hand to
avoid its whipping or damage.
• During cleaning you can adjust the suction
power, by turning the control knob (14) clock-
wise or counterclockwise, and also using me-
chanical regulator (3), located on the flexible
hose handle(4) (Fig.4).
MAINTENANCE
Removing dust from the collection container
Always use the vacuum cleaner only when the
dust collection container is installed. If in the col-
lection container no HEPA filter (21) or pre-filter
(20) is installed, the device electric motor can be
damaged, and such cases are not covered by
guarantee. Make sure that the filters are installed
correctly in the collection container.
• Turn off the vacuum cleaner using the ON/OFF
button (11) and disconnect it from the power
outlet.
• Press the flexible hose nozzle clamps (6) and
disconnect the hose from the device body.
• Press the collection container clamp button
(8) and remove the container.
• Press the button (19) to remove dust and
sweepings from the container (9).
• Close the container cover (18).
• Install the collection container (9) on its place,
by slightly pressing on it until clicking is heard
(Fig.5).
NOTE: we recommend cleaning the collection
container after each usage of the device.
Cleaning filters (20, 21) in the collection
container
Take care that the filters in the container are
clean, as the device effectiveness depends on
it. Clean the НЕРА filter no less than three-four
times a year, or oftener, if the filter becomes
ENGLISH
VT-1837_IM.indd 5 22.06.2012 16:49:17
Ваш отзыв будет первым