- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1834 B/GD, страница 5
5
ENGLISH
5
tachment (25, 26, 27) to the telescopic pipe. The
attachments (25, 26, 27) can be connected direct-
ly to the flexible hose’s handle (13).
• Adjust the telescopic pipe to the desired length by
pressing the locking button and stretching the pipe
to the desired length (Fig. 4).
• Extend the power cord to the desired length and
insert the plug into the outlet; turn on the vacuum
cleaner using the On/Off button (6).
Note: The yellow marking indicates the maximum
length of the power cord; do not extend the power
cord past the red marking.
• While operating the vacuum cleaner, adjust the
power level using the buttons (5).
- L Low power;
- M Medium power;
- H High power.
• To move from cleaning floor to cleaning carpets,
press the button on the brush (16) (Fig. 5). When
the bristles are extended from the brush, you are
in floor mode; when they are not – carpet mode.
• When finished cleaning, turn off the vacuum using
the power button (6), remove the power plug from
the outlet, press the cord wind button (7), holding
the power cord with your hand while winding.
• You can place the brush (16) into the “parking”
tray (3) for easy storage when the vacuum is not in
use.
CLEANING AND CARING FOR THE VACUUM
Removal of trash and dust:
• Open the lid (8) and remove the container (17).
• Remove the filter block (20) by pressing on its fas-
tener (19). (Fig. 1,2)
• Pour the dirty water out of the container (17).
Cleaning the filter block (20) (Fig. 6,7)
The filters (20b, 20с) must be clean three or four
times per year, or more frequently, depending upon
the level of dirtiness.
• Remove the filter block (20) by pressing on the
locks (19).
• Take apart the filter block (20) by turning the fas-
tener (20d) counter-clockwise - “open.”
• Wash the filter (20b) and screen filter (20с) under a
stream of warm water.
• Assemble the filter block (20), install the locks
(20d) and turn it clockwise – “close.”
Important:
• Before using the vacuum cleaner, make sure that
the filters (20b, 20с) are not damaged and that the
filter block (20) is installed in the container (17).
• While installing the filter 20b, observe its proper
fixation with the help of the supporting axle.
Cleaning the “НЕРА” filter (22) and preliminary
air filter (21) (Fig. 8)
• Open the lid (8) and remove the container (17).
• Remove the filters (21, 22) and clean off the dust.
The filters (21, 22) can be washed under a stream
of warm water and then allowed to dry thoroughly.
• Install the filters (21, 22), install the container (17)
and close the lid (8).
Important:
• While replacing the НЕРА-filter, do not forget to
use the rubber gasket 22а.
Note: Clean the HEPA filter no less frequently than
once or twice per year.
Cleaning the exhaust filter
• Open the lid (23) and remove the filter (24).
• Wash the filter under a stream of water and allow to
dry, install the filter (24) and close the lid (23).
Note: The filter should be cleaned at least once
per year.
Vacuum cleaner housing
• Wipe the vacuum cleaner housing with a damp
clothe.
• Do not allow liquids to get inside the vacuum
cleaner housing.
• Do not use solvents or abrasive cleaners to clean
the surfaces of the vacuum cleaner.
Technical characteristics:
Voltage: 220 V ~ 50 Hz
Power rating: 1800 Watts
Suction power: 400 Watts
Capacity of transparent water container: 2.5 liters
Noise Level: 92 dB
Specifications subject to change without prior
notice.
Service life of appliance - 5 years
GUARANTEE
Details regarding guarantee conditions can be
obtained from the dealer from whom the appliance
was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of
this guarantee.
This product conforms to the EMC-
Requirements as laid down by the Council
Directive 89/336/EEC and to the Law
Voltage Regulation (73/23 EEC)
ENGLISH
1834.indd 51834.indd 5 01.04.2010 15:06:1901.04.2010 15:06:19
Ваш отзыв будет первым