- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1815 G, страница 6
6
ENGLISH
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it off
immediately and check the telescopic pipe
and the flexible hose for obstruction. Unplug
the vacuum cleaner, remove the obstruction
and only after that you can continue cleaning.
Attention! Always switch the vacuum cleaner
on only with the dust bin (9), inlet (25), out-
let (5) and protective (30) filters installed.
Always make sure that the filters are installed
properly.
• Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket, the indicator (2)
will light up. The yellow mark on the power
cord warns about the maximum cord length.
Do not unwind the power cord further than
the red mark.
• Press the on/off (6) button to switch the vac-
uum cleaner on.
• During the operation you can control the suc-
tion power using the buttons (16) and (17) on
the flexible hose handle (13). The number of
glowing indicators (2) changes depending on
the selected power.
Attention! The flexible hose handle should
be kept along the line of sight of the vacuum
cleaner, otherwise the unit will not be able
to receive commands of the remote control.
• After the unit operation, switch the vacuum
cleaner off by pressing the on/off button (6)
or the button (15), and unplug the unit.
• To wind the power cord, press and hold the
button (1), hold the winding cord with the
hand to avoid its whipping and damage.
• Between unit operations, use the brush stor-
age (3).
• Use the handle (8) for carrying the vacuum
cleaner or the dust bin (9) (pic. 5).
AUTO SWITCH-OFF FUNCTION
• The vacuum cleaner is equipped with an auto
switch-off function in case of motor over-
heating.
• In case of overheating of the motor unit, the
automatic thermal switch will be on, and the
vacuum cleaner will be switched off.
• In this case remove the power plug from the
mains socket immediately.
• Check the telescopic pipe and the flexible
hose for obstruction and remove the obstruc-
tion.
• Let the vacuum cleaner cool down for approx-
imately 20-30 minutes before switching it on
again.
• Plug the unit into the mains, switch it on, if the
vacuum cleaner cannot be switched on, it may
be otherwise damaged. In this case contact
the authorized service center for repair.
CLEANING AND CARE
Remove garbage and dust from the dust bin (9),
disassemble and clean it after every usage of the
vacuum cleaner.
Start cleaning with the vacuum cleaner only after
having preliminarily removed dust and garbage
from the dust bin (9).
Removing the dust bin (9) and removal of
dust and garbage from it
• Switch the vacuum cleaner off and unplug it.
• Holding the handle (8), push the lock (7) and
remove the dust bin (9) (pic. 6).
• Place the dust bin over a garbage bin. Open
the lid (28) by pressing the lid lock (29) (pic.
7). Remove accumulated dust and garbage
from the dust bin (9).
Disassembling and cleaning of the dust bin
(9)
• Switch the vacuum cleaner off and unplug it,
take the dust bin (9) off, remove dust and gar-
bage from it.
• Holding the dust bin (9) by the flask (27), turn
the lid (23) counterclockwise till the mark
and take it off, the lid (23) must be taken off
together with the separator (26).
• Open the lid (23) by pressing the lock (24)
upwards.
• Take the microfoam and inlet filter (25) out.
Take the microfoam filter out and clean it from
dust.
• Clean the inlet filter (25) from dust.
• Wash the microfoam and inlet filters under
warm water jet and dry them thoroughly.
• Wash the separator (26) and the flask (27)
under warm water jet and dry them thor-
oughly.
Note: Before assembling the dust bin make sure
that all removable parts are clean and dry.
Assembling of the dust bin (9)
• Install the microfoam filter back to its place,
install the inlet filter (25) back to its place,
close the lid (23) until the lock (24) clicks.
VT-1815_IM.indd 6 12.02.2014 9:26:29
Ваш отзыв будет первым