- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1810 B, страница 29
29
E N G L I S H
• To avoid damages, transport the unit in origi-
nal package only.
• Watch over the batteries. Remove the batter-
ies from the battery compartment if you are
not going to use the unit for a long time.
• Keep the unit in a dry cool place out of reach
of children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
USING THE UNIT
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
Battery charging
Before using the unit for the first time or after a
long period of inactivity, the battery needs to be
charged for 4 hours.
• Remove the water tank (17) by pulling the lock
(16) towards you (pic. 1).
• Open the battery compartment lid and remove
the battery (14) (pic. 2).
• Install the battery (14) into the charger (6),
strictly following the polarity (pic. 3).
• Insert the power plug into the mains socket,
the indicator (7) will light up red.
• When the charging cycle is finished, the
indicator (7) will light green. The battery is
charged.
Notes:
- Charge the battery at the temperature from 0°
C to +35° C.
- If you haven’t used the unit for a month or
longer, charge the battery completely before
using.
Attention!
Battery leakage can cause injuries or damage
the unit. To avoid damages, follow the
recommendations specified below:
• insert the battery following the polarity;
• remove the battery if you are not planning to
use the unit for a long time;
• do not dismantle the battery, do not subject it
to high temperatures.
Assembling the sprayer
• Install the attachment holder (2) on the
sprayer (3), matching the ledges on the
sprayer (3) with the notches on the attach-
ment (2) and fix it till clicking of the locks, as
shown on the picture 4.
• Install and fix the attachment (1) on the holder
(2) as shown on the picture 5.
• Unscrew and remove the sprayer (3) from the
flask (5) (pic. 6).
• Pour the cleaning agent into the sprayer flask
(5).
• Install the sprayer back to its place.
Using the unit
• Select and install the required attachment (8
or 9) till clicking of the lock (pic. 7).
• Check if the battery (14) is installed properly.
• Pressing the sprayer handle (4), apply the
cleaning agent evenly on the surface and
then wipe the surface with the attachment
(1) (pic. 8).
Note: Wash the attachment (1) under a warm
water jet as it becomes dirty.
• Switch the unit on by pressing the button (11),
the operation indicator (12) will light up.
• To collect the liquid from the surface, move
the unit downwards.
Note: You may clean hard-to-reach surfaces in
horizontal position for a short period of time.
Attention!
If the battery (14) is low, the operation indicator
(12) starts blinking slowly and after some time
the unit will be switched off automatically.
During the breaks between cleaning cycles
switch the unit off; this allows to significantly
prolong the operation time of the unit within one
battery charging cycle.
Pour the dirty water out of the water tank as it is
filled up.
• After you finish the operation, switch the unit
off by pressing the button (11) and clean the
unit.
• Pour the dirty water out of the water tank (17)
as it is filled up; to do this, switch the unit off
by pressing the button (11), remove the water
tank by pulling the lock (16) towards you and
then remove the rubber plug (18) and pour the
water out (pic. 9).
VT-1810_7 land.indd 29 24.02.2014 9:50:00
Ваш отзыв будет первым