- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1805 B, страница 5
hose is blocked. Unplug the cord and remove
the blocking substance before you attempt to
start the vacuum cleaner again.
• Do not operate the vacuum cleaner too
close to heaters and like radiators, ciga-
rette butts, in areas where flammable or
combustible liquids are kept.
• Before you insert the plug into the wall out-
let, make sure your hand is dry.
• Before you start using the vacuum cleaner,
please remove large or sharp objects from
the floor in order to prevent the paper dust
bag damages.
• When you want to pull the plug from the wall
contact, please do this at the plug itself and
not by means of the electrical cable.
PREPARATION FOR USING
Unpack the vacuum cleaner. Verify the vacu-
um cleaner voltage meets the mains voltage
in your supply line before switching on.
Always switch off and unplug the vacuum
cleaner to change the nozzles or for mainte-
nance.
VACUUM CLEANER USAGE
• Verify the dust bag (17 or 23) and inlet filter
(16) are installed properly.
• Insert flexible hose end into air intake duct
(7) and turn it clockwise up to the stop. To
remove the flexible hose, turn the flexible
hose end (6) anticlockwise and pull it out
(Pic.1).
• Connect plastic extension tube (2) to hose
handle (4) (Pic. 2).
Plastic extension tubes (2)
• You can use one or two extension tubes
while operating. To connect them insert the
narrow end of one hose in the other hose
socket. (Pic. 3).
Carpet/floor brush (1)
• Connect brush (1) to extension tube (2)
(Pic. 4).
• Turn the switch on the brush in required po-
sition (depending on surface type which is
to be cleaned) (Pic. 5, 6).
Crevice nozzle (24)
To clean radiators, slits, corners, spaces be-
tween sofa pillows.
INSTRUCTIONS FOR USE
Before using the appliance, unwind a suf-
ficient length of the cord (19) and insert the
plug into the power supply. Yellow mark on
the cord indicates the maximum length of the
cord. Do not expend the cable beyond the red
mark. Switch the appliance on only if dust bag
(17 or 23) and filter (16) are installed prop-
erly.
• Push ON/OFF button (11) to switch on the
appliance.
• To wind the cord press button (14) while
holding the cord to escape damages.
• While operating you can adjust the suction
power turning regulator handle (12) clock-
or anticlockwise, and also using mechani-
cal regulator (3) on the flexible hose handle
(4) (Pic. 2).
MAINTENANCE
Use the appliance only if dust bag (17 or 23)
and inlet filter (16) are installed properly. If the
dust bag (17 or 23) or inlet filter (16) is absent,
the electric motor would be damaged. The
warranty does not extent to this case.
• Press button ON/OFF (11) to switch off the
appliance and unplug the cord from outlet.
• Turn flexible hose end (6) anticlockwise and
unplug it from the vacuum cleaner hous-
ing.
• Press dust bag compartment cap lock (8)
and open the cap.
• Press dust bag lock (15) and take the dust
bag (17 or 23) out.
• Remove plastic block lock (18) and unload
dust and trash from the dust bag. In case of
using paper dust bag, just utilize it.
• Install the plastic block lock on the cloth
dust bag (17), press the lock (15) and install
5
ENGLISH
Vt-1805.indd 5Vt-1805.indd 5 26.09.2006 10:28:1326.09.2006 10:28:13
Ваш отзыв будет первым