Бесплатные инструкции на русском языке
  • Тип техники
  • Бренд

Просмотр инструкции утюга Tefal GV7485E0 EXPRESS POWER ZONE, страница 22

Tefal
22
Easy descaling of your steam generator:
To extend the life of your steam generatorand avoidscale onyour ironing, your steam generator
is equipped with a built-in scale collector. This valve, located in the tank,
a
utomatically removes the scale that forms inside.
Operation:
An orange “anti-scale” light located on the control panel starts blinking to tell you that the anti-
scale valve needs rinsing - fig.12.
Important: This operation must not be carried out unless the steam generator has
been unplugged for at least two hours and has cooled down completely.
To carry out this operation, the steam generator must be close to a sink as water may
come out of the tank when it is opened.
Oncethe steam generator has cooled down completely, remove the scale collectorcover- fig. 13.
Unscrew theanti-scale valve andremove it fromthe housing;it contains thescalethat has built
up in the tank - fig.14 and fig.15.
To clean the valve properly, just rinse it under running water to remove the scale it contains -
fig.16.
Put the valve back into its housing and screw it in completely to keep it watertight - fig.17.
Refit the scale collector cover - fig. 18.
The next time you use your iron, press the “restart” button on the control panel to turn
off the orange “anti-scale” light.
D
o not use any descaling
substances (vinegar,
industrial descaling
p
roducts, etc.) when rinsing
the anti-scale valve :
they could damage it.
B
efore emptying your steam
generator, it must always be
left to cool for 2 hours to
avoid any risks of scalding.
Storing the steam generator
Press the illuminated on/off switch and unplug the generator.
Place the iron on the housing plate on the steam generator.
Raise the retaining hoop over the iron until it locks into place (audible click) - fig.2.
Your iron is then safely retained on its base. Warning: do not touch the soleplate while still hot.
Slot the extension cord outlet in the notch (depending on model). Take the end of the cord support and
press to return the flexible part into the base.
Store the steam cord in its slide storage place - fig.19. Take it, fold it in two so as to make a loop. Put the
end of this loop in the slide storage place then push gently until you see the end on the other side of the
slide storage place - fig.20.
Leave the steam generator to cool for at least one hour before putting it away if it is to be stored in a
cupboard or confined space.
You can store the steam generator in complete safety.
PROBLEMS CAUSES SOLUTIONS
The steam generator does not switch on
or the iron indicator and ON/OFF
indicator do not switch on.
The appliance is not switched on.
Check that your appliance is correctly
plugged in and press the illuminated
on/off switch.
Water runs out of the holes in the
soleplate.
Water has condensed in the pipes because
youareusing steam forthefirsttime oryou
have not used it forsometime.
Press on the steam control button away
from your ironing board until the iron
produces steam.
The soleplate is not hot enough.
Decrease the steam output while ironing
atlowtemperature(steam output control
dial on the control panel). Wait for the
thermostat light to go out before
activating the steam control button.
Your thermostat is faulty: the iron is not
hot enough.
Contact an Approved Service Centre.
Water streaks appear on the linen.
Your ironing board cover is soaked with
water as it is not suited to the power of a
steam generator.
Check that your ironing board is suitable
(See page 20).
Problems with your steam generator?
1800115593 TEFAL ExpressAnticalc:1800115593 5/02/09 11:36 Page 22
Ваш отзыв будет первым
Задайте вопрос
Ваше имя
E-mail
Вопрос*
Ваш вопрос будет опубликован после проверки
Ваш вопрос опубликован