- Тип техники
- Бренд
Просмотр инструкции плиты Indesit K 343 GS (R), страница 17
17
latter must be situated at a minimum of 420 mm abo ve
the hob. The minimum distance between the worktop
and kitchen units made of combustib le material is 700
mm.
e) The wall in direct contact with the back panel of the
cooker m ust be made of non-flammab le materials.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
Connecting the gas
The appliance should be connected to the mains or to a
gas cylinder in compliance with current directiv es. Bef ore
making the connection, check that the cooker is regulated
for the gas supply you are using. If not, follow the
instructions indicated in the paragraph “Adapting to
different types of gas”. On some models the gas supply
can be connected on the left or on the right, as necessary;
to change the connection, rev erse the position of the hose
holder with that of the cap and replace replace the gasket
(supplied with the appliance). When using liquid gas from
a cylinder, install a pressure regulator which complies with
current directiv e.
Important: check that the supply pressure complies with
the values indicated in table 1 “Characteristics of the
burners and nozzles” since this will ensure saf e operation,
correct consumption and ensure a longer life to your
appliance.
Connection with hose
Make the connection using a gas hose complying with
the the characteristics provided in current directive. The
internal diameter of the pipe used is as follows:
- 8mm f or liquid gas;
- 13mm f or methane gas .
When installing the hose, remember to tak e the following
precautions:
• No part of the hose should touch parts whose tempe-
rature e xceeds 50°C;
• The length of the hose should be less than 1500 mm;
• The hose should not be subject to twisting or pulling,
and should not have bends or kinks.
• The hose should not touch objects with sharp edges,
any mo ving parts, and it should not be crushed;
• The full length of the hose should be easy to inspect in
order to chec k its condition;
Check that the hose fits firmly into place at the two ends
and fix it with clamps complying to current directiv e.If any
of the above recommendations can not be adopted, flexible
metal pipes should be used.
Should the cooker be installed according to the conditions
of Class 2, subdivision 1, only a fle xible metal pipe which
is in compliance with current safety standards should be
used to make the connection to the gas mains .
Connecting a fle xible jointless stainless steel pipe
to a threaded attachment
Remov e the hose holder fitted on the appliance. The gas
supply pipe fitting is a threaded 1/2 gas cylindrical male
attachment. Only pipes and gaskets complying with current
directives. The full length of the pipe must not exceed 2000
mm.
Tight control
Important: when installation has been completed, check
the pipe fitting for leaks with a soap y solution. Nev er use a
flame. Once the connection has been made, ensure that
the flexible metal tube does not touch any moving par ts
and is not crushed.
Connecting the suppl y cable to the mains
Install a normalised plug corresponding to the load
indicated on the data plate. When connecting the cable
directly to the mains, install an omnipolar circuit-breaker
with a minimum contact opening of 3 mm between the
appliance and the mains. The omnipolar circuit breaker
should be sized according to the load and should comply
with current regulations (the earth wire should not be
interrupted by the circuit break er).
The supply cab le should be positioned so that it does not
reach a temperature of more than 50°C with respect to
the room temperature, along its length. Before making the
connection, check that:
• the limiter valve and the home system can support the
appliance load (see data plate);
• the mains is properly earthed in compliance with
current directiv es and regulations;
• there is easy access to the socket and omnipolar circuit
break er, once the hob has been installed.
N.B: never use reducers, adaptors or shunts since they
can cause heating or b urning.
Adapting the cooker to different types of gas
In order to adapt the cooker to a diff erent type of gas with
respect to the gas for which it was produced (indicated on
the label attached to the lid), f ollo w these steps:
a) replace the hose holder mounted on the appliance with
that supplied in the bag of “cook er accessories”.
Important: the hose holder for liquid gas is marked 8, the
hose holder f or methane gas is marked 13. Alwa ys fit the
sealing gasket.
b) Replacing the b urner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles f or the new type of gas
(see table 1 “Burner and nozzle characteristics”).
• replace all the components by repeating the steps in
re v erse order.
Ваш отзыв будет первым