- Тип техники
- Бренд
Просмотр инструкции блендера Vitek VT-8510, страница 5
5
E N G L I S H
• To switch the pulse mode on, set the
switch (7) to the position “P” and hold it for
several seconds.
• During the operation or between the opera-
tion cycles, you can add the required ingre-
dients into the bowl (3). To do this, turn the
measuring cup (1) clockwise and remove it
from the lid (2). After adding the ingredients
through the opening in the lid (2), place the
cup (1) back to its place and turn it counter
-
clockwise until it is fixed. The capacity of the
measuring cup (1) is 25 ml.
• After the unit operation is finished, set the
operation mode switch (7) to the «0» position
and unplug the unit.
• Remove the blender bowl (3) from the motor
unit (6) by turning it counterclockwise.
• Remove the lid (2) from the bowl (3).
• Take the processed products out of the
bowl (3).
• After the operation is finished, wash the
blender bowl (3).
Note:
– If food processing is hard, add some water,
liquor or juice into the blender bowl (3).
ATTENTION! Continuous operation time of
the blender should not exceed 1 minute; then
switch the unit off and let it cool down to room
temperature for at least 5 minutes.
CLEANING AND CARE
After the unit operation is finished, switch the
blender off by setting the operation mode
switch (7) to the “0” position and unplug it,
remove the blender bowl (3) from the motor
unit (6) as described in the chapter “USING THE
BLENDER”. Take the processed products out of
the bowl (3).
• Wash the bowl (3) preliminarily. To do this,
install the blender bowl (3) on the motor
unit (6) and turn it clockwise. Add some
washing solution into the bowl (3). Cover the
bowl (3) with the lid (2) with installed mea
-
suring cup (1). Insert the power plug into the
mains socket.
• Set the switch (7) to the position “P” and hold
it for several seconds.
• After that set the operation mode switch (7)
to the position «0» and unplug the unit.
• Remove the blender bowl (3) from the motor
unit (6) by turning it counterclockwise.
• Remove the lid (2) from the bowl (3).
• Pour out the washing solution from the bowl
(3) and rinse the bowl (3).
• Wash the measuring cup (1), the lid (2) and
the bowl (3) with warm water adding some
soft detergent, then rinse them and dry.
• Remove the knife block (5) and the sealing
gasket (4). To remove the knife block (5) turn
it counterclockwise and remove.
WARNING: The knife block (5) cutting edges
are very sharp and dangerous. Handle the knife
block very carefully.
• Wash the knife block (5) (only from the knives
side) and the sealing gasket (4) with warm
water and soft detergent and dry them.
• You can wash the blender bowl (3) in a dish-
washing machine after removing the knife
block (5).
• Set the sealing gasket (4) on the knife
block (5).
• Insert the knife block (5) into the blender
bowl (3) and turn it clockwise.
• To avoid damage of the sealing gasket (4)
when installing the knife block (5), do not
apply excessive effort.
• Clean the motor unit (6) with a soft, slightly
damp cloth and then wipe it dry.
• Do not use coarse sponges, abrasives and
solvents to clean the blender.
• Do not immerse the blender motor unit (6)
into any liquids; do not wash it in a dishwash
-
ing machine.
• Do not put the removable parts of the blender
in a dishwashing machine as well.
STORAGE
• Perform the requirements of the CLEANING
AND CARE section before taking the unit
away for storage.
• Keep the unit out of reach of children and
people with disabilities.
DELIVERY SET
Table blender – 1 pc.
Manual – 1 pc.
TECHNICAL SPECIFICATIONS
Power supply: 220-240 V ~ 50 Hz
Rated input power: 350 W
Maximum power: 900 W
Bowl capacity: 1,5 L
IM VT-8510.indd 5 06.03.2019 14:20:23
Ваш отзыв будет первым
Вопросы пользователей
Поиск:
по производителю
по типу техники
по модели
Сортировать:
по дате
c ответами
Ирина Ивановна Фоминых
28 июня 2021, Пермь
Здравствуйте, сняли ножи с блендера VT 8510 vitek, как их установить обратно?
0 ответов
Ответить
0