- Тип техники
- Бренд
Просмотр инструкции соковыжималки Vitek VT-3661, страница 4
4
ENGLISH
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
• Check the power cord and plug periodi-
cally.
• Never use the slow juicer if the mesh filter,
the power cord or the power plug is dam-
aged, if the unit works improperly or after it
was dropped.
• Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least 3 hours at
room temperature before switching on.
• Unpack the slow juicer.
Disassemble and clean the slow juicer
before usage:
• Remove the pusher (1) from the lid (4) feed-
ing chute (3).
• Remove the tray (2) from the chute (3).
• Turn the lid (4) counterclockwise until bump-
ing and remove the lid (4).
• Remove the processing bowl (8) from the
motor unit (12).
• Remove the screw (5) from the processing
bowl (8).
• Remove the mesh filter (6) with the separa-
tor (7) from the bowl (8), remove the separa-
tor (7) from the filter (6).
• Wash the removable parts that will contact
products thoroughly with warm water and a
neutral detergent and dry them.
• Clean the motor unit (12) with a slightly damp
cloth and then wipe it dry.
• Use the slow juicer on a dry, flat and stable
surface, away from heat sources, moisture,
open flame and direct sunlight.
ASSEMBLING THE SLOW JUICER
Important! Make sure that the silicone gas-
ket (11) is set properly in the bottom part of
the processing bowl (8). The silicone gasket
must seal the pulp channel tightly, otherwise
leakage of juice from the bowl (8) may cause
damage to the unit. When cleaning the unit,
move the silicone gasket (11) aside to open
the pulp channel.
If some liquid or juice gets into the motor unit,
switch the unit off and apply to the authorized
service center.
1. Set the processing bowl (8) on the motor
unit (12).
2. Put the separator (7) on the mesh filter (6).
Install the filter (6) with the separator (7) in
the bowl (8), to do this turn the filter (6) clock-
wise/counterclockwise until the pulp outlet
channels match.
3. Install the screw (5) inside the bowl (8), apply-
ing little effort; turn it slightly to provide secure
fitting of the screw (5) on the drive axis.
4. Place the lid (4) on the processing bowl (8)
and turn it clockwise until bumping.
5. Install the tray (2) on the feeding chute (3).
USING THE SLOW JUICER
Important! Before switching the unit on,
make sure that all parts are installed prop-
erly. Do not switch the unit on without the
products intended for processing. Fruit, veg-
etables and berries intended for processing
must be fresh.
• Before juice extracting remove inedible parts
from vegetables or fruit, such as stems, hard
peel or stones, for example, cherry or peach.
• Wash the fruit or vegetables and chop them
into pieces easily fitting into the feeding chute
(3) openings.
• Place the slow juicer on a flat stable surface.
• Place the containers (14, 15) under the juice
(9) and pulp spouts.
• Open the juice draining spout (9) by lifting the
lid (10).
• Insert the power plug into the mains socket.
• Switch the slow juicer on by setting the
switch (13) to the position «ON».
Operation mode switch (13) position
«ON» – the juicer is on.
«O» – the juicer is off.
«R» – reverse, the screw (5) reverse rotation
mode.
IM VT-3661.indd 4 29.01.2018 15:17:33
Ваш отзыв будет первым