- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-8130 BK, страница 5
5
E N G L I S H
Attachment (27)
Use the attachment (27) to clean the furniture
upholstery.
Attachment holder (28)
Install the holder (28) on the telescopic pipe (4)
and install the attachments (26) and (27) on it.
Dust bin (11)
The dust bin (11) is equipped with the cyclonic
filter which eliminates garbage and dust from
the air, and the filter block (15) retains the finest
dust particles.
Note:
– provide that the filter block (15) is always
clean, because the overall performance of
the vacuum cleaner depends on it.
USING THE VACUUM CLEANER
Safety measures
• Do not use the vacuum cleaner near hot sur-
faces, such as ashtrays and in places where
inflammable liquids are stored.
• Take sharp objects away from the floor before
cleaning to prevent unit damage.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it off
immediately and check the telescopic pipe (4)
and the flexible hose (7) for obstruction.
Switch the vacuum cleaner off, then unplug
it, remove the obstruction and only after that
continue cleaning.
OPERATION
Attention! You may switch the vacuum cleaner
on only with the dust bin (11), with the filter
block (15) and the outlet HEPA filter (25) installed
in the dust bin. Before switching the vacuum
cleaner on always make sure that the filters
(15, 25) are installed properly.
• Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket.
• The yellow mark on the power cord indicates
the maximum cord length. Do not unwind the
power cord further than the red mark.
• Press the on/off button (20) to switch the vac-
uum cleaner on.
• During the operation you can control the suc-
tion power using the power control (21) and
the manual suction power control (6) on the
flexible hose handle (5).
• After room cleaning switch the vacuum
cleaner off by pressing the on/off button (20)
and unplug the unit.
• To wind the power cord, press the button (19),
hold the winding cord with your hand to avoid
its whipping and damage.
• During the breaks you can place the brush (1)
in the brush storage (22).
CLEANING AND CARE
Cleaning the dust bin (11)
Remove garbage and dust from the dust bin (11)
after every room cleaning.
– Switch the vacuum cleaner off and unplug it.
– Holding the handle (12), press the lock (18)
and remove the dust bin (11) (pic. 5).
– Place the dust bin (11) over a garbage bin.
– Move the clamp button (13) to release the
lid (14) lock and open the lid (14).
– Remove accumulated dust and garbage from
dust bin (11) (pic. 6).
– Close the lid (14).
– Install the dust bin (11) back to its place.
Cleaning the filter block (15) installed
in the dust bin (11)
– Preliminarily remove dust and garbage from
the dust bin (11) as described above.
– Lift the clamp (16) and open the lid (17).
– Remove the filter block (15) (pic. 7).
– Remove the foam filter.
– Clean the filters from dust and garbage and
wash them under warm water jet.
– Do not wash filters in a dishwashing machine.
– Dry the filters thoroughly.
– Do not dry filters with a hairdryer.
– Wash the dust bin (11), wipe it and dry.
– Install the foam filter back to its place, install
the filter block (15), close the lid (17) and
make sure that the lid (17) is secured.
– Install the assembled dust bin (11) back to its
place and make sure that the dust bin (11) is
fixed properly.
Attention!
Before installing the dust bin (11) make sure that
the filters are dry and there is no moisture inside
the dust bin (11).
Cleaning the outlet HEPA filter (25)
• Switch the vacuum cleaner off and unplug it.
• Remove the outlet filter grid (24) by pressing
the lock (23) and remove the HEPA filter (25).
IM VT-8130.indd 5 23.03.2017 16:09:18
Ваш отзыв будет первым