- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-8124 B, страница 5
5
E N G L I S H
USING THE VACUUM CLEANER
Safety measures
• Do not use the vacuum cleaner near hot sur-
faces, such as ashtrays and in places where
inflammable liquids are stored.
• Take sharp objects away from the floor before
cleaning to prevent unit damage.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it
off immediately and check the telescopic
pipe (16) or the flexible hose (13) for obstruc-
tion. Switch the vacuum cleaner off, unplug it,
remove the obstruction and only after that you
can continue cleaning.
OPERATION
Attention! Switch the vacuum cleaner on only
with the dustbag (19 or 20) and inlet (21) and
outlet (23, 24) filters installed. Always make sure
that the filters (21, 23, 24) are installed properly.
• Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket.
• The yellow mark on the power cord indicates
the maximum cord length. Do not unwind the
power cord further than the red mark.
• Press the ON/OFF button (7) to switch the
vacuum cleaner on.
• During the operation you can control the suc-
tion power using the electronic suction power
control (5) and the manual suction power con-
trol (11) on the flexible hose handle (12).
• After room cleaning switch the vacuum
cleaner off by pressing the ON/OFF button (7)
and unplug the unit.
• To wind the power cord, press the power cord
winding button (6), hold the winding cord with
your hand to avoid its whipping and damage.
CLEANING AND CARE
• If the full dustbag indicator (4) turns «red»
during the vacuum cleaner operation, replace
the paper (20) dustbag or clean up the cloth
(19) dustbag.
Note: - the paper dustbag (20) is disposable,
dispose of the dustbag (20) when it is filled up.
• Before cleaning the cloth dustbag (19) switch
the vacuum cleaner off and unplug it.
• Open the dustbag compartment lid (3) press-
ing on the lid lock.
• Remove the dustbag holder (18) with the
dustbag (19).
• Take the dustbag (19) out from the holder (18).
• To clean the cloth dustbag (19) place it above
the trash bin and remove the plastic clamp. If
necessary, wash the cloth dustbag (19) with
warm water and neutral detergent and dry
thoroughly, after that install the plastic clamp
back to its place.
• Install the dustbag (19 or 20) into the
holder (18).
• Install the dustbag holder (18) back to its place.
• Close the dustbag compartment lid (3),
slightly press on the lid (3) until locking.
Note:
– do not try to close the lid (3) without the dust-
bag holder (18) installed, otherwise you can
damage the locking system;
– always make sure that the dustbag holder (18)
and the dustbag (19 or 20) are installed prop-
erly before closing the dustbag compartment
lid (3).
CLEANING THE FILTERS
Provide that the inlet filter (21), the outlet HEPA-
filter (23) and the foam filter (24) are always
clean, because the overall performance of the
vacuum cleaner depends on it; clean the filters
(21, 23, 24) no less than 3-4 times a year, and
more often at severe obstruction.
Cleaning the inlet filter (21)
• Switch the vacuum cleaner off and unplug it.
• Open the dustbag compartment lid (3) press-
ing on the lid lock.
• Remove the dustbag holder (18) with the
dustbag.
• Press the inlet filter grid (21) clamp and
remove the grid.
• Wash the inlet foam filter with warm water, dry
it thoroughly and install the filter and the grid
(21) back to its place.
Notes: - before installing the foam filter make
sure that it is clean and dry.
• Install the dustbag holder (18) with the dust-
bag installed back to its place.
• Close the dustbag compartment lid (3).
Cleaning the outlet HEPA filter (23)
and the foam filter (24)
• Switch the vacuum cleaner off and unplug it.
• Remove the outlet filter grid (22) by pressing
the clamp and remove the HEPA filter (23).
• Wash the HEPA filter (23) under slightly warm
water jet. Do not wash filters in a dishwash-
ing machine.
IM VT-8124.indd 5 11.05.2017 14:30:05
Ваш отзыв будет первым