- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-8115 OG, страница 6
6
ENGLISH
furniture surface as well, the pile on the com-
bined brush (26) prevents damage to polished
furniture surface.
USING THE VACUUM CLEANER
Safety measures
• Do not use the vacuum cleaner near hot
surfaces, ashtrays and in the places where
inflammable liquids are stored.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch it
off immediately and check the telescopic
pipe and the flexible hose for obstruction.
Switch the vacuum cleaner off, then unplug
it, remove the obstruction and only after that
continue cleaning.
Attention! Always switch the vacuum cleaner
on only with the dust bin (8), inlet (19) and
outlet (4) filters installed. Always make sure
that the filters are installed properly.
Attention! To avoid scratching the floor
remove the transportation safety accesso-
ries before using the vacuum cleaner. To do
this, turn the unit over and remove the pro-
tective ring (24) and the protective plate (25).
– Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket. The yellow mark
on the power cord warns about the maximum
cord length. Do not unwind the power cord
further than the red mark.
– Press the button (5) to switch the vacuum
cleaner on.
– During the unit operation you can control the
suction power with the control (17).
– After the unit operation, switch the vacuum
cleaner off by pressing the button (5) and
unplug the unit.
– To wind the cord, press and hold down the
button (1), hold the winding cord with hand to
avoid its whipping and damage.
– Between the vacuum cleaner operations, use
the brush storage (2).
– Use the handle (7) for carrying the vacuum
cleaner or the dust bin (8) (pic. 5).
AUTO SWITCH-OFF FUNCTION
• The vacuum cleaner is equipped with auto
switch-off function in case of motor over-
heating.
• In case of overheating of the motor, the auto-
matic thermal switch will be on, and the vac-
uum cleaner will be switched off.
• In this case immediately remove the power
plug from the mains socket.
• Check the telescopic pipe and the flexible
hose for obstruction and remove the obstruc-
tion.
• Let the vacuum cleaner cool down for approx-
imately 20-30 minutes before switching it on
again.
• Plug the vacuum cleaner into the mains,
switch it on, if the unit can not be switched on,
this may mean that it is otherwise damaged.
In this case contact an authorized service
center for repair.
CLEANING AND CARE
Remove garbage and dust, disassemble and
clean the dust bin (8) after every usage of the
vacuum cleaner.
Start cleaning with the vacuum cleaner only after
having preliminarily removed dust and waste
from the dust bin (8).
Taking off the dust bin (8) and removing
dust and waste from it
– Switch the vacuum cleaner off and unplug it.
– Remove the flexible hose (11) by turning the
flexible hose ending (10) counterclockwise.
– Holding the handle (7), push the lock (6) and
remove the dust bin (8).
– Place the dust bin over a garbage bin. Open
the lower lid (23) by pressing the lid lock (24)
(pic. 6). Remove accumulated dust and waste
from the dust bin (8).
Disassembling and cleaning
of the dust bin (8)
– Switch the vacuum cleaner off and unplug it,
– Press the lock (6) and remove the dust
bin (8).
– Open the lower lid (22) by pressing the lid lock
(23) and remove dust and waste from the dust
bin (8). Close the lower lid (22).
– Holding the dust bin (8) by the flask (21), turn
the lid (18) counterclockwise and take it off
(рис. 7).
– Clean the inlet filter (19) from dust. To do this,
remove the microfoam insert from the filter
body (19).
– Wash the inlet filter (19) and the microfoam
insert under warm water jet and dry them
thoroughly.
– Take the separator from the flask (21), holding
the separator (20) by its ledges.
VT-8115.indd 6 29.03.2016 14:54:04
Ваш отзыв будет первым