- Тип техники
- Бренд
Просмотр инструкции пылесоса Vitek VT-1895 B/R, страница 6
6
ENGLISH
off immediately and check the telescopic
pipe and the flexible hose for obstruction.
Switch the vacuum cleaner off, then unplug
it, remove the obstruction and only after that
continue cleaning.
Attention! Always switch the vacuum cleaner
on only with the dust bin (8), inlet (20) and
outlet (4) filters installed. Always make sure
that the filters are installed properly.
- To avoid scratching the floor remove the
following details before using the vacuum
cleaner: the protective ring (25) and the
protective plate (26).
– Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket. The yellow mark
on the power cord warns about the maximum
cord length. Do not unwind the power cord
further than the red mark.
– Press the button (5) to switch the vacuum
cleaner on.
– During the unit operation you can control the
suction power with the manual control (13) on
the flexible hose handle (12).
– After the unit operation switch the vacuum
cleaner off by pressing the button (5) and
unplug the unit.
– To wind the power cord, press and hold down
the button (1), hold the winding cord with
hand to avoid its whipping and damage.
– Between operations use the brush storage (2).
– Use the handle (7) for carrying the vacuum
cleaner or the dust bin (8) (pic. 5).
AUTO SWITCH-OFF FUNCTION
• The vacuum cleaner is equipped with auto
switch-off function in case of motor unit over-
heating.
• In case of overheating of the motor unit, the
automatic thermal switch will be on, and the
vacuum cleaner will be switched off.
• In this case remove the power plug from the
mains socket immediately.
• Check the telescopic pipe and flexible hose
for obstruction and remove the obstruction.
• Let the vacuum cleaner cool down for approx-
imately 20-30 minutes before switching it on
again.
• Plug the vacuum cleaner into the mains,
switch it on, if the unit can not be switched
on, this may mean, that it is otherwise dam-
aged. In this case contact an authorized ser-
vice center for repair.
CLEANING AND CARE
Remove garbage and dust from the dust bin (8),
disassemble and clean it after every usage of the
vacuum cleaner.
Start cleaning with the vacuum cleaner only after
having preliminarily removed dust and garbage
from the dust bin (8).
Detaching of the dust bin (8) and removal
of dust and garbage from it
– Switch the vacuum cleaner off and unplug it.
– Remove the flexible hose (11) by turning
the flexible hose ending (10) counterclockwise.
– Holding the handle (7), push the lock (6) and
detach the dust bin (8).
– Place the dust bin over a garbage bin. Open
the lower lid (23) by pressing the lid lock
button (24) (pic. 6). Remove accumulated
dust and garbage from the dust bin (8).
Disassembling and cleaning
of the dust bin (8)
– Switch the vacuum cleaner off and unplug it.
– Press the lock (6) and detach the dust bin (8).
– Open the lower lid (23) by pressing the lid lock
(24) and remove dust and garbage from the
dust bin (8). Close the lower lid (23).
– Holding the dust bin (8) by the flask (22), turn
the lid (19) counterclockwise and take it off
(pic. 7).
– Clean the inlet filter (20) from dust, to do this,
remove the microfoam insert from the filter
body (20).
– Wash the inlet filter (20) and the microfoam
insert under a warm water jet and then dry
them thoroughly.
– Take the separator (21) by the ledges and
remove it from the flask (22).
– Wash the separator (21) and the dust bin
flask (22) under warm water jet and dry them
thoroughly.
Attention: Before assembling the dust bin,
make sure that all removable parts are clean
and dry.
Assembling of the dust bin (8)
– Insert the separator (21) into the dust bin flask
(22). To do this, match the ledges on the sep-
arator (21) with the grooves corresponding by
place and form on the flask (22).
– Install the microfoam insert into the inlet fil-
ter body (20).
VT-1895.indd 6 30.07.2015 10:44:41
Ваш отзыв будет первым