- Тип техники
- Бренд
Просмотр инструкции лобзика Bosch GST 140 CE, страница 12
12 | English
2 609 932 772 | (29.3.11) Bosch Power Tools
f Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
f Do not direct the light beam at persons or
animals and do not stare into the light beam
yourself (not even from a distance).
f Check the tight seating of the saw blade.
A loose saw blade can fall out and lead to in-
juries.
f Use a narrow saw blade when sawing tight
curves.
f When ejecting the saw blade, hold the ma-
chine in such a manner that no persons or
animals can be injured by the ejected saw
blade.
f Dusts from materials such as lead-contain-
ing coatings, some wood types, minerals
and metal can be harmful to one’s health
and cause allergic reactions, lead to respi-
ratory infections and/or cancer. Materials
containing asbestos may only be worked by
specialists.
– As far as possible, use a dust extraction
system suitable for the material.
– Provide for good ventilation of the work-
ing place.
– It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
f Prevent dust accumulation at the work-
place. Dusts can easily ignite.
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
f The restarting protection feature prevents
uncontrolled restarting of the machine af-
ter an interruption in the power supply. To
restart the operation, switch the On/Off
switch
to the Off position and start the ma-
chine again.
f The contact protector attached to the casing
(see figure 17, page 227) prevents acciden-
tal touching of the saw blade during the
working procedure and may not be removed.
f Before sawing in wood, particle boards,
building materials etc., check for foreign
objects, such as nails, screws, etc. and re-
move them as required.
f Plunge cuts may only be applied to soft ma-
terials, such as wood, gypsum board, etc.
f The metal overshoe prevents the plastic
footplate from being scratched up, espe-
cially when sawing metal.
f Adapt the settings of your power tool to the
respective application. For example, reduce
the stroke rate and orbital action when cut-
ting metal or for tight curved cuts.
f When working small or thin work pieces, al-
ways use a sturdy support or a saw table
(accessory).
f In extreme conditions, always use dust ex-
traction as far as possible. Blow out ventila-
tion slots frequently and install a residual
current device (RCD). When working metals,
conductive dust can settle in the interior of
the power tool. The total insulation of the
power tool can be impaired.
f Products sold in GB only: Your product is fit-
ted with a BS 1363/A approved electric plug
with internal fuse (ASTA approved to
BS 1362).
If the plug is not suitable for your socket out-
lets, it should be cut off and an appropriate
plug fitted in its place by an authorised cus-
tomer service agent. The replacement plug
should have the same fuse rating as the orig-
inal plug.
The severed plug must be disposed of to
avoid a possible shock hazard and should
never be inserted into a mains socket else-
where.
Products sold in AUS and NZ only: Use a re-
sidual current device (RCD) with a rated re-
sidual current of 30 mA or less.
Symbols
The following symbols are important for reading
and understanding the operating instructions.
Please take note of the symbols and their mean-
ing. The correct interpretation of the symbols
will help you to use the machine in a better and
safer manner.
OBJ_BUCH-1320-002.book Page 12 Tuesday, March 29, 2011 12:39 PM
Ваш отзыв будет первым