- Тип техники
- Бренд
Просмотр инструкции шлифмашины Bosch GGS 28 CE, страница 17
English | 17
Bosch Power Tools 3 609 929 C06 | (16.12.10)
f Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, sand-
ing drum for cracks, tear or excess wear,
wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect
for damage or install an undamaged acces-
sory. After inspecting and installing an ac-
cessory, position yourself and bystanders
away from the plane of the rotating acces-
sory and run the power tool at maximum no-
load speed for one minute. Damaged acces-
sories will normally break apart during this
test time.
f Wear personal protective equipment. De-
pending on application, use face shield,
safety goggles or safety glasses. As appro-
priate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stop-
ping small abrasive or workpiece frag-
ments. The eye protection must be capable
of stopping flying debris generated by vari-
ous operations. The dust mask or respirator
must be capable of filtrating particles gener-
ated by your operation. Prolonged exposure
to high intensity noise may cause hearing
loss.
f Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken ac-
cessory may fly away and cause injury be-
yond immediate area of operation.
f Hold power tool by insulated gripping sur-
faces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting ac-
cessory contacting a “live” wire may make ex-
posed metal parts of the power tool “live”
and could give the operator an electric
shock.
f Always hold the tool firmly during the start-
up. The reaction torque of the motor, as it ac-
celerates to full speed, can cause the tool to
twist.
f Use clamps to support workpiece whenever
practical. Never hold a small workpiece in
one hand and the tool in the other hand
while in use. Clamping a small workpiece al-
lows you to use both hands to control the
tool. Round material such as dowel rods,
pipes or tubing have a tendency to roll while
being cut, and may cause the bit to bind or
jump toward you.
f Position the cord clear of the spinning ac-
cessory. If you lose control of the power tool,
the cord may be cut or snagged and your
hand or arm may be pulled into the spinning
accessory.
f Never lay the power tool down until the ac-
cessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
f After changing the bits or making any adjust-
ments, make sure the collet nut, chuck or
any other adjustment devices are securely
tightened. Loose adjustment devices can un-
expectedly shift, causing loss of control, loose
rotating components will be violently thrown.
f Do not run the power tool while carrying it
at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
f Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the
housing and excessive accumulation of pow-
dered metal may cause electrical hazards.
f Do not operate the power tool near flamma-
ble materials. Sparks could ignite these ma-
terials.
f Do not use accessories that require liquid
coolants. Using water or other liquid cool-
ants may result in electrocution or shock.
Kickback and related warnings
f Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accesso-
ry which in turn causes the uncontrolled
power tool to be forced in the direction op-
posite of the accessory’s rotation at the
point of the binding.
OBJ_BUCH-1269-003.book Page 17 Thursday, December 16, 2010 4:05 PM
Ваш отзыв будет первым